1-800-315-4345
Summary
- Flush the air and other non-condensable gases out of the copper line set and indoor unit
- Alternative for the inefficient and expensive quick-connect line sets
- Cost-effective, simple, and quick evacuation
- Perfect for most people and installations
Description
Pioneer KWIK-E-VAC is an all-new, revolutionary, patented kit designed to simplify the installation process. This product is intended to provide an alternative to a vacuum pump, a tool that was previously required to install mini splits.
KWIK-E-VAC works by flushing the air and other non-condensable gases out of the copper line set and indoor unit combination, in order to ensure that the refrigerant in the system remains contaminant-free. In order to bleed the lines of any air and check for leaks, a vacuum pump and pressure gauges were previously needed. This kit allows the user to bypass that step, making any mini-split system truly DIY.
Use this as an alternative for the inefficient and expensive quick-connect line sets, which reduce system efficiency and capacity, and cost 10 times more than the cost of this kit. A cost-effective, simple, and quick evacuation, perfect for most people and installations.
Weighs 8.5 ounces when empty.
This kit provides an alternative way to install a split air conditioner, if a proper vacuum pump is not available for the evacuation of the line sets. See below instructions, only to replace the specific section in the installation manual covering the use of a vacuum pump for evacuation. Follow all remaining instructions in the manual as originally written.
- Read all safety instructions above and wear protective gear as suggested.
- Keep the metal can upright at all times while using. Do not tilt or tip.
- Ensure the electrical power to entire equipment is switched off at the main breaker.
- Indoor section of the air conditioner: Connect both copper pipes of the line set to the indoor unit properly and as instructed in the equipment installation manual, using proper torque, methods, and materials approved by the equipment manufacturer.
- Outdoor section of the air conditioner: Connect ONLY THE GAS SIDE copper pipe (one with larger diameter) to the GAS side service valve of the outdoor unit properly and as instructed in the equipment installation manual, using proper torque, methods and materials approved by the equipment manufacturer. Do not connect the LIQUID SIDE copper pipe (one with smaller diameter) at this time, until instructed further below.
- Connect the end connector of hose of the purging kit to the SERVICE PORT on the GAS SIDE SERVICE VALVE of the outdoor unit tightly. Pay attention to prevent valve damage.
- Turn the valve on the flushing kit can tap valve clockwise, reaching all the way down.
- You should hear the flow of flushing material flowing into the GAS side of the copper line set and then flowing out freely at unconnected pipe end of the LIQUID side of the copper line set near the outdoor unit. Once flow is confirmed, close the tap valve, then open again for 5 seconds at a time, repeating until about 2/3 of contents in the can are used up. Close the tap valve of the can. (Valve turns CW to open and CCW to close).
- If no flow of the material is noticed when first opened, close the flushing kit tap valve, disengage the hose connector from the service port, and adjust the depressor inside the hose connector outward by 1 or 2 turns, and repeat the steps 5 through 7 above.
- Now it is time to quickly connect LIQUID SIDE copper pipe (one with smaller diameter) to the LIQUID side service valve of the outdoor unit properly and as instructed in the equipment installation manual, using proper torque, methods and materials approved by the equipment manufacturer. At this stage all 4 pipe connectors are tightly connected.
- Open the tap valve again and release the remaining material in the can into the system until contents are entirely used up. Disconnect the hose from the service port of the unit.
- Using soapy bubbles spray, carefully check all 4 pipe connections for leaks. If the leaks are present, tighten, adjust, or repair the connection to stop any leaks, and repeat evacuation.
- While the purging hose remains attached to the service port, unscrew the tap valve from the top of the canister to release all remaining gas pressure, and wait until all purging material pressure is entirely released. Disconnect the hose from the service port.
- Follow the installation instructions provided by the equipment manufacturer for the next steps, such as opening the service valves to release the refrigerant, other verifications, and further startup procedures. For multi-zone systems, use one kit for each zone.
WARNING for California residents only: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Warning: Use only as directed. Read label instructions carefully.
- Keep out of reach of children. Intentional misuse by deliberately concentrating and/or inhaling contents may be fatal. Vapors are heavier than air and may spread along floors. Avoid breathing vapors or mist. Avoid contact with skin, eyes, and clothing. Provide sufficient air exchange and /or exhaust in work areas. Handle in accordance with good industrial hygiene and safety practice. THIS PRODUCT IS FOR OUTDOOR USE ONLY.
- Contains gas under pressure, may explode if heated. Flammable gas. Do not spray on an open flames or other ignition sources. Keep away from heat. Vapors may form flammable mixture with air. The products should only be used in areas from which all sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard. No sparking tools should be used. Take measures to prevent the build-up of electrostatic charge. Keep away from open flames, hot surfaces, and sources of ignition. When using DO NOT SMOKE. Disconnect the electrical power to the equipment.
- Pressurized container: Do not pierce or burn, even after use. Do not store in enclosed vehicles. Protect from sunlight. Store in a well-ventilated place. Store at temperatures not exceeding 120 degrees F / 49 degrees C. Keep container tightly closed and in a dry and well-ventilated location. Store in original container. The product has and indefinite shelf life when stored properly.
- Ensure adequate ventilation, especially in confined areas. Use respiratory protection if needed. Wear safety glasses with side shields. Direct contact with liquid may cause frostbite. Wear proper protective gloves when using.
Contains: 1,1-Difluoroethane which has zero ozone depletion potential and a very low global warming potential. See MSDS for additional safety information at here: https://minisplitsystemsdirect.com/pages/material-safety
Instructional Video
Thank you for visiting and shopping at Mini Split Systems Direct. Following are the terms and conditions that constitute our Shipping Policy.
Domestic Shipping Policy
Shipment processing time
All orders made before 2:00 PM EST are processed within 2-3 business days. Items ordered on weekends (Saturday or Sunday) start to process and ship as early as the following business day.
If we are experiencing a high volume of orders, shipments may be delayed by a few days. Please allow additional days in transit for delivery. If there will be a significant delay in shipment of your order, we will contact you via email or telephone.
Shipping rates & delivery estimates
We offer standard free shipping via UPS Ground, FedEx Ground, and Freight for all orders in the United States. We do not currently ship to international locations.
| Destination | Shipping method | Processing Time | Estimated Delivery Time | Shipment cost |
| United States | Free Shipping |
2 - 3 business days | 3 - 7 days | Free |
Delivery delays can occasionally occur.
Shipment confirmation & Order tracking
You will receive a Shipment Confirmation email once your order has shipped containing your tracking number(s). The tracking number will be active within 24 hours.
Customs, Duties and Taxes
Mini Split Systems Direct is not responsible for any customs and taxes applied to your order. All fees imposed during or after shipping are the responsibility of the customer (tariffs, taxes, etc.).
Damages & Missing Items
Please inspect all packages for damaged or missing items before accepting your shipment. If any of the items are missing or appear to have any type of damage; Mark the Receipt Damaged and/or missing (write which items are missing, or damaged and describe the damage).
Only refuse the items that are damaged, keep and sign for the items that are in good condition and be sure to notate the items that are being refused for damages clearly on the delivery receipt. You must contact our Customer Service Department at info@minisplitsystemsdirect.com to report which product(s) were missing and/or refused for damages and which product(s) were accepted at the time of delivery. After our Shipping Department receives confirmation from the Freight LTL Company we will promptly ship out the replacement product(s) to you.
Although Mini Split Systems Direct is NOT responsible for shipping damage, if your item(s) do arrive damaged, please send photos to info@minisplitsystemsdirect.com and we can assist with filing a claim against the shipping carrier to cover the cost of damages.
Any damages or missing items have to be noted on the delivery receipt prior to signing for and accepting your shipment in order to file a claim. Do not let the delivery driver rush you. It is your right to inspect each and every item.
Pre-Orders, Backorders, and Out-of-Stock Items:
Mini Split Systems Direct is dedicated to sourcing any item you may need and getting it to you as quickly as possible. Any items that are out of stock, or available for Pre-Order will be noted on the product page. You are welcome to place an order for Pre-Order items, backorder items, and for items that are out of stock, and will ship them the second they become available from the manufacturer, ensuring you get the item before anyone else. If you have questions about lead times, please refer to the product page or contact us at info@minisplitsystemsdirect.com or give a call or text at 1-800-315-4345
Returns
We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.
To be eligible for a return, your item must be in the same condition that you received it, unused and in its original packaging.
All returns are subject to a 15% restocking fee, and the purchaser is responsible for the cost of return shipping.
To start a return, you can contact us at info@minisplitsystemsdirect.com or call us at 1-800-315-4345. If your return is accepted, we will either schedule a pickup or send you a return shipping label, as well as instructions on how and where to send your package. Items sent back without first requesting a return will not be accepted.
You can always contact us for any return questions at info@minisplitsystemsdirect.com, or call us at 1-800-315-4345.
Refunds
We will notify you once we’ve received and inspected your return, and let you know if the refund was approved or not. If approved, you’ll be automatically refunded on your original payment method. A 15% restocking fee and the cost of return shipping will be deducted from the refund. Please allow up to 10 business days for your bank or credit card company to process and post the refund to your account. If you have any questions regarding your refund, please contact us at info@minisplitsystemsdirect.com or call us at 1-800-315-4345.
Cancellations
All orders canceled after 24 hours are subject to a 5% administration fee, If your order has not been shipped yet, this is the only fee you will incur. This is a fee that covers administrative and personnel fees.
If your order has been shipped, you will not be charged a 5% administration fee, the standard return procedures will apply and you will be responsible for the cost of return shipping, and a 15% restocking fee will be ducted from your refund. Refunds will only be issued to the original payment method that you used when placing your order.
Damages and issues
Please inspect all packages for damaged or missing items before accepting your shipment. If any of the items are missing or appear to have any type of damage; Mark the Receipt Damaged and/or missing (write which items are missing, or damaged and describe the damage).
Only refuse the items that are damaged, keep and sign for the items that are in good condition and be sure to notate the items that are being refused for damages clearly on the delivery receipt. You must contact our Customer Service Department at info@minisplitsystemsdirect.com to report which product(s) were missing and/or refused for damages and which product(s) were accepted at the time of delivery. After our Shipping Department receives confirmation from the Freight LTL Company we will promptly ship out the replacement product(s) to you.
Although Mini Split Systems Direct is NOT responsible for shipping damage, if your item(s) do arrive damaged, please send photos to info@minisplitsystemsdirect.com and we can assist with filing a claim against the shipping carrier to cover the cost of damages.
Any damages or missing items have to be noted on the delivery receipt prior to signing for and accepting your shipment in order to file a claim. Do not let the delivery driver rush you. It is your right to inspect each and every item.
Exchanges
The fastest way to ensure you get what you want is to return the item you have (see return process above), and once the return is accepted, make a separate purchase for the new item.
Our goal is to consistently provide the best pricing in the marketplace online and we work very diligently to do so. If you happen to see another online shop that offers a lower price than us within six months of your date please let us know and we’ll be happy to refund the difference on your original payment method. Moreover, because we are consistently working with our suppliers to get better rates we know that you can feel very comfortable and confident that you are seeing the best prices that can be provided for the products listed on our site.
Moving forward if you find the same item that we carry on another website that has a lower price please submit that to us within six months of your purchase date and we will refund you the difference.
If it is a case of seeing a lower price on another website and we need to send a partial refund simply email us the link to the exact product and brand from our site and also the link from our competitors site so we can inspect the pricing. Again this needs to be within six months from the date of your order and we will review your submission and apply a credit if necessary.
Our 100% Shoppers Best Price Guarantee has some limitations:
- The item must have already been purchased from our site prior to asking for this to be reviewed and submitted.
- This does not include rebate programs or specific retailer programs such as buy three get one free type offers or any combination such as that are not eligible.
- The item will need to be in stock from the competitors site that you’re submitting the information from.
- The competitor must be an online store, they may not have a retail location, warehouse, showroom, or physical location.
- The website cannot be a wholesaler, liquidator, distributor, or auction website. Examples are eBay, Liquadation.com, Via Trading, Overstock, Wayfair, Amazon, Home Depot, Lowes, etc.
- The competitor must also be someone who has been authorized by the supplier and/or manufacturer to resell the product you are inquiring about.
- The price match will include the product listing price, but will exclude any sales tax.
Description
Summary
- Flush the air and other non-condensable gases out of the copper line set and indoor unit
- Alternative for the inefficient and expensive quick-connect line sets
- Cost-effective, simple, and quick evacuation
- Perfect for most people and installations
Description
Pioneer KWIK-E-VAC is an all-new, revolutionary, patented kit designed to simplify the installation process. This product is intended to provide an alternative to a vacuum pump, a tool that was previously required to install mini splits.
KWIK-E-VAC works by flushing the air and other non-condensable gases out of the copper line set and indoor unit combination, in order to ensure that the refrigerant in the system remains contaminant-free. In order to bleed the lines of any air and check for leaks, a vacuum pump and pressure gauges were previously needed. This kit allows the user to bypass that step, making any mini-split system truly DIY.
Use this as an alternative for the inefficient and expensive quick-connect line sets, which reduce system efficiency and capacity, and cost 10 times more than the cost of this kit. A cost-effective, simple, and quick evacuation, perfect for most people and installations.
Weighs 8.5 ounces when empty.
This kit provides an alternative way to install a split air conditioner, if a proper vacuum pump is not available for the evacuation of the line sets. See below instructions, only to replace the specific section in the installation manual covering the use of a vacuum pump for evacuation. Follow all remaining instructions in the manual as originally written.
- Read all safety instructions above and wear protective gear as suggested.
- Keep the metal can upright at all times while using. Do not tilt or tip.
- Ensure the electrical power to entire equipment is switched off at the main breaker.
- Indoor section of the air conditioner: Connect both copper pipes of the line set to the indoor unit properly and as instructed in the equipment installation manual, using proper torque, methods, and materials approved by the equipment manufacturer.
- Outdoor section of the air conditioner: Connect ONLY THE GAS SIDE copper pipe (one with larger diameter) to the GAS side service valve of the outdoor unit properly and as instructed in the equipment installation manual, using proper torque, methods and materials approved by the equipment manufacturer. Do not connect the LIQUID SIDE copper pipe (one with smaller diameter) at this time, until instructed further below.
- Connect the end connector of hose of the purging kit to the SERVICE PORT on the GAS SIDE SERVICE VALVE of the outdoor unit tightly. Pay attention to prevent valve damage.
- Turn the valve on the flushing kit can tap valve clockwise, reaching all the way down.
- You should hear the flow of flushing material flowing into the GAS side of the copper line set and then flowing out freely at unconnected pipe end of the LIQUID side of the copper line set near the outdoor unit. Once flow is confirmed, close the tap valve, then open again for 5 seconds at a time, repeating until about 2/3 of contents in the can are used up. Close the tap valve of the can. (Valve turns CW to open and CCW to close).
- If no flow of the material is noticed when first opened, close the flushing kit tap valve, disengage the hose connector from the service port, and adjust the depressor inside the hose connector outward by 1 or 2 turns, and repeat the steps 5 through 7 above.
- Now it is time to quickly connect LIQUID SIDE copper pipe (one with smaller diameter) to the LIQUID side service valve of the outdoor unit properly and as instructed in the equipment installation manual, using proper torque, methods and materials approved by the equipment manufacturer. At this stage all 4 pipe connectors are tightly connected.
- Open the tap valve again and release the remaining material in the can into the system until contents are entirely used up. Disconnect the hose from the service port of the unit.
- Using soapy bubbles spray, carefully check all 4 pipe connections for leaks. If the leaks are present, tighten, adjust, or repair the connection to stop any leaks, and repeat evacuation.
- While the purging hose remains attached to the service port, unscrew the tap valve from the top of the canister to release all remaining gas pressure, and wait until all purging material pressure is entirely released. Disconnect the hose from the service port.
- Follow the installation instructions provided by the equipment manufacturer for the next steps, such as opening the service valves to release the refrigerant, other verifications, and further startup procedures. For multi-zone systems, use one kit for each zone.
WARNING for California residents only: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Warning: Use only as directed. Read label instructions carefully.
- Keep out of reach of children. Intentional misuse by deliberately concentrating and/or inhaling contents may be fatal. Vapors are heavier than air and may spread along floors. Avoid breathing vapors or mist. Avoid contact with skin, eyes, and clothing. Provide sufficient air exchange and /or exhaust in work areas. Handle in accordance with good industrial hygiene and safety practice. THIS PRODUCT IS FOR OUTDOOR USE ONLY.
- Contains gas under pressure, may explode if heated. Flammable gas. Do not spray on an open flames or other ignition sources. Keep away from heat. Vapors may form flammable mixture with air. The products should only be used in areas from which all sources of ignition have been excluded. Electrical equipment should be protected to the appropriate standard. No sparking tools should be used. Take measures to prevent the build-up of electrostatic charge. Keep away from open flames, hot surfaces, and sources of ignition. When using DO NOT SMOKE. Disconnect the electrical power to the equipment.
- Pressurized container: Do not pierce or burn, even after use. Do not store in enclosed vehicles. Protect from sunlight. Store in a well-ventilated place. Store at temperatures not exceeding 120 degrees F / 49 degrees C. Keep container tightly closed and in a dry and well-ventilated location. Store in original container. The product has and indefinite shelf life when stored properly.
- Ensure adequate ventilation, especially in confined areas. Use respiratory protection if needed. Wear safety glasses with side shields. Direct contact with liquid may cause frostbite. Wear proper protective gloves when using.
Contains: 1,1-Difluoroethane which has zero ozone depletion potential and a very low global warming potential. See MSDS for additional safety information at here: https://minisplitsystemsdirect.com/pages/material-safety
Instructional Video
Shipping Policy
Thank you for visiting and shopping at Mini Split Systems Direct. Following are the terms and conditions that constitute our Shipping Policy.
Domestic Shipping Policy
Shipment processing time
All orders made before 2:00 PM EST are processed within 2-3 business days. Items ordered on weekends (Saturday or Sunday) start to process and ship as early as the following business day.
If we are experiencing a high volume of orders, shipments may be delayed by a few days. Please allow additional days in transit for delivery. If there will be a significant delay in shipment of your order, we will contact you via email or telephone.
Shipping rates & delivery estimates
We offer standard free shipping via UPS Ground, FedEx Ground, and Freight for all orders in the United States. We do not currently ship to international locations.
| Destination | Shipping method | Processing Time | Estimated Delivery Time | Shipment cost |
| United States | Free Shipping |
2 - 3 business days | 3 - 7 days | Free |
Delivery delays can occasionally occur.
Shipment confirmation & Order tracking
You will receive a Shipment Confirmation email once your order has shipped containing your tracking number(s). The tracking number will be active within 24 hours.
Customs, Duties and Taxes
Mini Split Systems Direct is not responsible for any customs and taxes applied to your order. All fees imposed during or after shipping are the responsibility of the customer (tariffs, taxes, etc.).
Damages & Missing Items
Please inspect all packages for damaged or missing items before accepting your shipment. If any of the items are missing or appear to have any type of damage; Mark the Receipt Damaged and/or missing (write which items are missing, or damaged and describe the damage).
Only refuse the items that are damaged, keep and sign for the items that are in good condition and be sure to notate the items that are being refused for damages clearly on the delivery receipt. You must contact our Customer Service Department at info@minisplitsystemsdirect.com to report which product(s) were missing and/or refused for damages and which product(s) were accepted at the time of delivery. After our Shipping Department receives confirmation from the Freight LTL Company we will promptly ship out the replacement product(s) to you.
Although Mini Split Systems Direct is NOT responsible for shipping damage, if your item(s) do arrive damaged, please send photos to info@minisplitsystemsdirect.com and we can assist with filing a claim against the shipping carrier to cover the cost of damages.
Any damages or missing items have to be noted on the delivery receipt prior to signing for and accepting your shipment in order to file a claim. Do not let the delivery driver rush you. It is your right to inspect each and every item.
Pre-Orders, Backorders, and Out-of-Stock Items:
Mini Split Systems Direct is dedicated to sourcing any item you may need and getting it to you as quickly as possible. Any items that are out of stock, or available for Pre-Order will be noted on the product page. You are welcome to place an order for Pre-Order items, backorder items, and for items that are out of stock, and will ship them the second they become available from the manufacturer, ensuring you get the item before anyone else. If you have questions about lead times, please refer to the product page or contact us at info@minisplitsystemsdirect.com or give a call or text at 1-800-315-4345
Return and Refund Policy
Returns
We have a 30-day return policy, which means you have 30 days after receiving your item to request a return.
To be eligible for a return, your item must be in the same condition that you received it, unused and in its original packaging.
All returns are subject to a 15% restocking fee, and the purchaser is responsible for the cost of return shipping.
To start a return, you can contact us at info@minisplitsystemsdirect.com or call us at 1-800-315-4345. If your return is accepted, we will either schedule a pickup or send you a return shipping label, as well as instructions on how and where to send your package. Items sent back without first requesting a return will not be accepted.
You can always contact us for any return questions at info@minisplitsystemsdirect.com, or call us at 1-800-315-4345.
Refunds
We will notify you once we’ve received and inspected your return, and let you know if the refund was approved or not. If approved, you’ll be automatically refunded on your original payment method. A 15% restocking fee and the cost of return shipping will be deducted from the refund. Please allow up to 10 business days for your bank or credit card company to process and post the refund to your account. If you have any questions regarding your refund, please contact us at info@minisplitsystemsdirect.com or call us at 1-800-315-4345.
Cancellations
All orders canceled after 24 hours are subject to a 5% administration fee, If your order has not been shipped yet, this is the only fee you will incur. This is a fee that covers administrative and personnel fees.
If your order has been shipped, you will not be charged a 5% administration fee, the standard return procedures will apply and you will be responsible for the cost of return shipping, and a 15% restocking fee will be ducted from your refund. Refunds will only be issued to the original payment method that you used when placing your order.
Damages and issues
Please inspect all packages for damaged or missing items before accepting your shipment. If any of the items are missing or appear to have any type of damage; Mark the Receipt Damaged and/or missing (write which items are missing, or damaged and describe the damage).
Only refuse the items that are damaged, keep and sign for the items that are in good condition and be sure to notate the items that are being refused for damages clearly on the delivery receipt. You must contact our Customer Service Department at info@minisplitsystemsdirect.com to report which product(s) were missing and/or refused for damages and which product(s) were accepted at the time of delivery. After our Shipping Department receives confirmation from the Freight LTL Company we will promptly ship out the replacement product(s) to you.
Although Mini Split Systems Direct is NOT responsible for shipping damage, if your item(s) do arrive damaged, please send photos to info@minisplitsystemsdirect.com and we can assist with filing a claim against the shipping carrier to cover the cost of damages.
Any damages or missing items have to be noted on the delivery receipt prior to signing for and accepting your shipment in order to file a claim. Do not let the delivery driver rush you. It is your right to inspect each and every item.
Exchanges
The fastest way to ensure you get what you want is to return the item you have (see return process above), and once the return is accepted, make a separate purchase for the new item.
Price Match Policy
Our goal is to consistently provide the best pricing in the marketplace online and we work very diligently to do so. If you happen to see another online shop that offers a lower price than us within six months of your date please let us know and we’ll be happy to refund the difference on your original payment method. Moreover, because we are consistently working with our suppliers to get better rates we know that you can feel very comfortable and confident that you are seeing the best prices that can be provided for the products listed on our site.
Moving forward if you find the same item that we carry on another website that has a lower price please submit that to us within six months of your purchase date and we will refund you the difference.
If it is a case of seeing a lower price on another website and we need to send a partial refund simply email us the link to the exact product and brand from our site and also the link from our competitors site so we can inspect the pricing. Again this needs to be within six months from the date of your order and we will review your submission and apply a credit if necessary.
Our 100% Shoppers Best Price Guarantee has some limitations:
- The item must have already been purchased from our site prior to asking for this to be reviewed and submitted.
- This does not include rebate programs or specific retailer programs such as buy three get one free type offers or any combination such as that are not eligible.
- The item will need to be in stock from the competitors site that you’re submitting the information from.
- The competitor must be an online store, they may not have a retail location, warehouse, showroom, or physical location.
- The website cannot be a wholesaler, liquidator, distributor, or auction website. Examples are eBay, Liquadation.com, Via Trading, Overstock, Wayfair, Amazon, Home Depot, Lowes, etc.
- The competitor must also be someone who has been authorized by the supplier and/or manufacturer to resell the product you are inquiring about.
- The price match will include the product listing price, but will exclude any sales tax.
12,000 BTU 25 SEER ACiQ Platinum Single Zone Slim Ceiling Cassette Mini Split System w/ Extreme Heat
Line Set Length
12,000 BTU 25.5 SEER ACiQ Platinum Single Zone Ceiling Cassette Mini Split System w/ Extreme Heat
Installation Kit Options
12,000 BTU 25.5 SEER ACiQ Platinum Single Zone Wall Mount Mini Split System - Extreme Heat - WiFi Enabled
Installation Kit Options
12,000 BTU 25.5 SEER2 ACiQ Platinum Single Zone Floor Mount Mini Split System w/ Extreme Heat
Installation Kit Options
18,000 BTU 21.5 SEER2 ACiQ Platinum Single Zone Ceiling Cassette Mini Split System w/ Extreme Heat
Installation Kit Options
18,000 BTU 22 SEER2 ACiQ 2-Zone Wall Mounted Mini Split System - Extreme Heat - WiFi Enabled - 9K + 9K
Line Set Length for 9K Air Handler #1/Line Set Length for 9K Air Handler #2
18,000 BTU 22.9 SEER2 ACiQ 2-Zone Ceiling Cassette Mini Split System - 9+9
Choose Line Set Length for 9K Air Handler #1/Choose Line Set Length for 9K Air Handler #2
18,000 BTU 22.9 SEER2 ACiQ 2-Zone Wall Mounted Mini Split System w/ WiFi - 9K + 9K
Lineset Length for 9K Air Handler #1/Lineset Length for 9K Air Handler #2
18,000 BTU 25 SEER ACiQ Platinum Single Zone Slim Ceiling Cassette Mini Split System w/ Extreme Heat
Line Set Length
12,000 BTU 25 SEER ACiQ Platinum Single Zone Slim Ceiling Cassette Mini Split System w/ Extreme Heat
Line Set Length
12,000 BTU 25.5 SEER ACiQ Platinum Single Zone Ceiling Cassette Mini Split System w/ Extreme Heat
Installation Kit Options
12,000 BTU 25.5 SEER ACiQ Platinum Single Zone Wall Mount Mini Split System - Extreme Heat - WiFi Enabled
Installation Kit Options
12,000 BTU 25.5 SEER2 ACiQ Platinum Single Zone Floor Mount Mini Split System w/ Extreme Heat
Installation Kit Options
18,000 BTU 21.5 SEER2 ACiQ Platinum Single Zone Ceiling Cassette Mini Split System w/ Extreme Heat
Installation Kit Options
18,000 BTU 22 SEER2 ACiQ 2-Zone Wall Mounted Mini Split System - Extreme Heat - WiFi Enabled - 9K + 9K
Line Set Length for 9K Air Handler #1/Line Set Length for 9K Air Handler #2
18,000 BTU 22.9 SEER2 ACiQ 2-Zone Ceiling Cassette Mini Split System - 9+9
Choose Line Set Length for 9K Air Handler #1/Choose Line Set Length for 9K Air Handler #2
18,000 BTU 22.9 SEER2 ACiQ 2-Zone Wall Mounted Mini Split System w/ WiFi - 9K + 9K
Lineset Length for 9K Air Handler #1/Lineset Length for 9K Air Handler #2
18,000 BTU 25 SEER ACiQ Platinum Single Zone Slim Ceiling Cassette Mini Split System w/ Extreme Heat
Line Set Length
12,000 BTU 25 SEER ACiQ Platinum Single Zone Slim Ceiling Cassette Mini Split System w/ Extreme Heat
Line Set Length
12,000 BTU 25.5 SEER ACiQ Platinum Single Zone Ceiling Cassette Mini Split System w/ Extreme Heat
Installation Kit Options
12,000 BTU 25.5 SEER ACiQ Platinum Single Zone Wall Mount Mini Split System - Extreme Heat - WiFi Enabled
Installation Kit Options
12,000 BTU 25.5 SEER2 ACiQ Platinum Single Zone Floor Mount Mini Split System w/ Extreme Heat
Installation Kit Options
18,000 BTU 21.5 SEER2 ACiQ Platinum Single Zone Ceiling Cassette Mini Split System w/ Extreme Heat
Installation Kit Options
18,000 BTU 22 SEER2 ACiQ 2-Zone Wall Mounted Mini Split System - Extreme Heat - WiFi Enabled - 9K + 9K
Line Set Length for 9K Air Handler #1/Line Set Length for 9K Air Handler #2
18,000 BTU 22.9 SEER2 ACiQ 2-Zone Ceiling Cassette Mini Split System - 9+9
Choose Line Set Length for 9K Air Handler #1/Choose Line Set Length for 9K Air Handler #2
18,000 BTU 22.9 SEER2 ACiQ 2-Zone Wall Mounted Mini Split System w/ WiFi - 9K + 9K
Lineset Length for 9K Air Handler #1/Lineset Length for 9K Air Handler #2
18,000 BTU 25 SEER ACiQ Platinum Single Zone Slim Ceiling Cassette Mini Split System w/ Extreme Heat
Line Set Length
Related Products
