HVAC Mirage | 24,000 BTU | 23 SEER2 | Outdoor Condenser | 220V | OMZH241C | Ventus X Series | Single-Zone Component

The HVAC Mirage OMZH241C (Ventus X Series) is a 24,000 BTU, 23 SEER2 inverter-driven outdoor condenser built for homeowners and contractors who need high-efficiency variable-speed cooling in a 2-ton footprint. Note: This listing is for the outdoor condenser component only — a compatible indoor air handler, line set, and electrical accessories must be purchased separately to form a complete operational system.

Engineered for variable-speed comfort, the OMZH241C's inverter-driven compressor continuously modulates output to match real-time load — eliminating the on/off cycling of single-stage equipment and maintaining tighter temperature tolerances while consuming less energy over a full season. At 23 SEER2, this condenser exceeds current federal minimum efficiency thresholds for the Southern region and qualifies as a high-efficiency unit for utility rebate programs in most states.

Outdoor Condenser
(OMZH241C)

Installation Requirements & Accessories

• Electrical Requirement: Dedicated 220V (208-230V / 60Hz) Single-Phase circuit. Breaker size [NEEDS VERIFICATION — confirm with full electrical spec sheet].
• Line Set Required (NOT Included): 3/8" Liquid x 7/8" Suction copper refrigerant line set — sized to your installation run length.
• Indoor Unit NOT Included: This is a component-only listing. A compatible HVAC Mirage indoor air handler must be purchased separately.
• Mounting Hardware NOT Included: Wall mounting brackets, electrical whip, and disconnect box must be sourced separately.
• Not Compatible With: 115V-only circuits.

Pro-Installer Tip: Leaking flare connections are the leading cause of refrigerant loss and premature compressor failure on residential mini splits. Use an Eccentric Flaring Tool (not a standard impact flare tool) to produce a bubble-tight, uniform flare seat, then torque each fitting to manufacturer specification using a calibrated Digital Torque Wrench — do not estimate by feel. Before opening service valves, pull and hold a vacuum below 500 microns for a minimum of 15 minutes; a rising vacuum after isolation indicates a leak or residual moisture that will convert to acid inside the refrigerant circuit. For the communication wiring between indoor and outdoor units, use 14/4 AWG stranded copper — undersized or solid-conductor wire is the most common source of "E1" communication fault codes on inverter-driven systems. All refrigerant handling must be performed by an EPA Section 608-certified technician in compliance with 40 CFR Part 82.

Key Benefits

• 23 SEER2 Efficiency: Exceeds federal minimum thresholds for Southern region compliance and qualifies for utility efficiency rebates in most states.
• Variable-Speed Inverter Compressor: Continuously modulates output to match real-time load — no on/off cycling, tighter temperature control, lower peak draw.
• R-410A Factory Pre-Charged: Ships with refrigerant charge complete; technician evacuates, confirms charge, and opens service valves during installation.
• 2-Ton Capacity (24,000 BTU): Appropriate for residential spaces typically 1,000–1,500 sq ft, subject to Manual J load calculation.
• 7-Year / 5-Year Warranty Coverage: Industry-leading compressor and parts warranty when installed by a licensed professional and registered with HVAC Mirage.

Technical Specifications

Compatibility & Fitment

• Compatible With: Dedicated 220V (208-230V) single-phase electrical circuits.
• Compatible With: HVAC Mirage Ventus X Series indoor air handlers (confirm matched AHRI-certified model pairing before ordering).
• NOT Compatible With: 115V-only circuits — this unit will not operate on standard 120V household outlets.
• NOT Included: Indoor air handler — must be purchased separately.
• NOT Included: Copper line set (3/8" liquid x 7/8" suction) — must be purchased separately.
• NOT Included: Mounting brackets, electrical disconnect box, electrical whip, or conduit.

Frequently Asked Questions

Is professional installation required to keep the warranty valid, or is this a true DIY kit?

Professional installation by a licensed HVAC technician is strictly required. This is a standard flare-connection system that requires evacuation to below 500 microns before opening service valves. It is not a pre-charged, no-vacuum DIY kit. The 7-Year Compressor / 5-Year Parts Limited Warranty is only valid when installed by a licensed professional and when the product is registered.

Is the line set included, and if not, what size do I need to buy?

The line set is NOT included with this outdoor condenser. You will need a copper refrigerant line set with a 3/8" liquid line and a 7/8" suction line, sized appropriately for your run length.

Does this listing include everything needed to cool a room?

No. This listing is for the outdoor condenser component (OMZH241C) only. To form a complete, operational mini split system, you must separately purchase: a compatible HVAC Mirage indoor air handler, a copper line set (3/8" liquid x 7/8" suction), electrical disconnect box, mounting hardware, and have it installed by a licensed HVAC contractor.

What voltage circuit does this outdoor condenser require?

This unit requires a dedicated 220V (208-230V / 60Hz / Single-Phase) circuit. It is NOT compatible with standard 115V household circuits.

Compliance & Warranty

This unit carries a 7-Year Compressor and 5-Year Parts Limited Warranty from HVAC Mirage. Warranty coverage is contingent upon installation by a licensed HVAC professional and product registration with HVAC Mirage. All refrigerant work must be performed by an EPA Section 608-certified technician in compliance with 40 CFR Part 82. GTIN/UPC: [NEEDS VERIFICATION — not present in source data]. MPN: [NEEDS VERIFICATION — not populated in source data; SKU OMZH241C used in structured data].