This is the bus bar and wire kit that connects two SimpliPhi batteries inside a BOSS-6 enclosure, built for installers who need a clean, factory-matched wiring path rather than a cobbled-together cable run.
SimpliPhi builds battery accessories to match specific enclosure configurations rather than as universal parts, and this bus bar and wire kit follows that same philosophy — it is matched to the BOSS-6 enclosure running two batteries. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fitment & Requirements
- Designed for a 2-battery configuration inside the SimpliPhi BOSS-6 enclosure.
- SKU BB-2-6 identifies this as the bus bar and wire kit variant for that specific 2-battery, BOSS-6 setup.
- Wire gauge, ampacity limit, voltage rating, and terminal lug size are not specified in manufacturer data provided — confirm these against the BOSS-6 manual before installation. [NEEDS VERIFICATION]
- Not confirmed for use with other SimpliPhi enclosure models or different battery counts. [NEEDS VERIFICATION]
- Not confirmed as compatible with non-SimpliPhi battery or enclosure hardware.
Bus bar connections between paralleled batteries are a common source of loose-terminal heating, especially when torque specs aren't followed to the letter. Under-torqued lugs increase contact resistance, and that resistance shows up as heat during high-current charge/discharge cycles — a direct path toward thermal runaway risk at the connection point, not just an inverter fault code. Verify every bus bar terminal with a digital torque wrench set to the manufacturer's specified value before the enclosure is closed up. Torque values for this kit were not included in the data provided to us, so pull the exact figure from the BOSS-6 manual in the Resources tab rather than guessing — NEC guidance on listed connectors is clear that torque must match the hardware manufacturer's spec, not a generic table.
Key Benefits
- Matched to SimpliPhi's own BOSS-6 enclosure design rather than a generic universal fit.
- Simplifies wiring for a 2-battery parallel setup with a purpose-built bus bar.
- Keeps battery interconnections organized and consistent with OEM enclosure layout.
- Sourced as a single SKU (BB-2-6) for straightforward ordering and replacement.
| Spec | Value | Unit |
|---|---|---|
| SKU | BB-2-6 | — |
| Battery Configuration | 2 | batteries |
| Enclosure Compatibility | BOSS-6 | — |
| Price | 332.99 | USD |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Fits: SimpliPhi BOSS-6 enclosure configured for 2 batteries.
- Does NOT have confirmed fitment for other BOSS enclosure sizes or battery counts. [NEEDS VERIFICATION]
- Does NOT have confirmed fitment for non-SimpliPhi enclosures or third-party battery packs.
Compliance & Environment
| Item | Value |
|---|---|
| UL Listing | [NEEDS VERIFICATION] |
| NEC Ampacity Reference | [NEEDS VERIFICATION] |
| IP Rating | [NEEDS VERIFICATION] |
FAQ
What system is this bus bar and wire kit designed for?
This kit is designed for the SimpliPhi BOSS-6 enclosure in a 2-battery configuration.
Does this kit fit other SimpliPhi enclosures or battery counts?
Fitment beyond the 2-battery BOSS-6 configuration is not confirmed in manufacturer data provided to us. Confirm with your BOSS enclosure documentation before ordering. [NEEDS VERIFICATION]
What wire gauge and terminal sizes come with this kit?
Gauge and terminal lug sizes were not provided in the manufacturer data available to us. [NEEDS VERIFICATION]
Is this kit sold as a complete bus bar and wire set?
Yes. It is listed as a bus bar and wire kit for connecting 2 batteries inside the BOSS-6 enclosure, SKU BB-2-6.
Warranty & Registration
Manufacturer warranty terms for this kit were not included in the data provided to us. Please refer to the "Resources (System Manuals and Warranty)" Tab above on this page for the manufacturer's warranty documentation and registration details. [NEEDS VERIFICATION]
