This package pairs a 12V HUSKY2 LiFePO4 battery with the Links2 Node 12 control system and the Links2 Vision 10 embedded monitor. It is built for RVs, boats, and small off-grid homes that need battery storage plus a wired control hub for lighting, tanks, and other 12V loads.
Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Why This Combination Matters
A battery is only half the equation on an RV or off-grid build. Without a control system, you are stuck wiring relays and switches by hand for every tank sensor, light, and pump. The Links2 Node 12 and Vision 10 monitor give you a single point of control and monitoring, wired directly to a 12V LiFePO4 battery built for daily-cycle use. This is a system-level purchase, not just a battery: verify wiring compatibility with your existing RV harness before install.
Battery Characteristics
The 12V HUSKY2 uses LiFePO4 (Lithium Iron Phosphate) chemistry, built with Tier 1 LFP cells. It stores 5.12kWh of usable energy per unit. The case is IP65-rated for dust and water resistance, and the battery includes self-heating for cold-weather charging protection. An internal BMS manages charge and discharge safety.
Wiring & Configuration Limits
[NEEDS VERIFICATION] — DATA does not state maximum series/parallel expansion limits for the 12V HUSKY2. Do not assume series or parallel stacking counts without confirming against the manufacturer documentation referenced in the Resources tab.
The Links2 Node 12 operates on 9-18V input, drawing a maximum input current of 80A. It is designed to integrate with a 12V system such as the HUSKY2, not with 24V or 48V battery banks. Do not wire the Node 12 into a higher-voltage bank without a compatible LinksWell-approved configuration [NEEDS VERIFICATION on higher-voltage support].
Pro-Installer Tip
Cold ambient temperatures are the most common cause of premature lithium cell damage in RV installs, because charging a LiFePO4 cell below freezing accelerates lithium plating and permanent capacity loss. The HUSKY2's self-heating function addresses this by warming the cells before allowing charge current in, which prevents cell imbalance and BMS lockout events down the road. Confirm the self-heating function is drawing correctly with a shunt-based battery monitor before your first cold-weather charge cycle. As a professional standard, plan your daily discharge around 80-100% DoD for LiFePO4, but avoid repeated full 100% cycles if you want to maximize long-term cycle life.
Key Benefits
- 5.12kWh of usable LiFePO4 energy storage per unit
- IP65 casing for outdoor and marine-adjacent exposure
- Self-heating for cold-weather charge protection
- Inverter communications included on this INV variation
- Links2 Node 12 control hub with 30A x 4 and 10A x 8 dimmable PWM output channels
- 10.1-inch Vision 10 embedded monitor with smartphone app control via Links2 APP
Technical Table
| Spec | Value |
|---|---|
| Voltage | 12V |
| Energy Capacity | 5.12kWh |
| Chemistry | LiFePO4 |
| Enclosure Rating | IP65 |
| Cold Weather Protection | Self-heating |
| Control System Operating Voltage | 9-18V |
| Control System Max Input Current | 80A |
| Control System Output Channels | 30A x 4 (2 Set H-Bridge), 10A x 8 (Dimmable PWM) |
| Override Switches | 12 |
| Digital Input Channels | 12 (12 Channels) |
| Temperature Sensor Inputs | 2 PCS |
| Tank Sensor Inputs | 4 PCS |
| Fuel Sensor Inputs | 4 PCS |
| LPG Sensor Inputs | 4 PCS |
| Voltage Sensor Input | 1 PCS |
| Node 12 Interfaces | RJ45 (RS485) x 3, 4-pin (RS485) x 1, RJ45 (CAN/RV-C) x 1, USB Type-A x 1 |
| Monitor Screen Size | 10.1 inches |
| Monitor Screen Resolution | 1024 x 600 |
| Monitor Interfaces | RS485 & RVC |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
This system is compatible with RVs, boats, and small off-grid homes running on a 12V architecture. The Links2 Node 12 supports connectivity via RJ45 RS485, 4-pin RS485, RJ45 CAN/RV-C, and USB Type-A, allowing integration with other RV components using matching protocols. The Vision 10 monitor connects via RS485 and RVC and supports OTG firmware upgrades and USB device connectivity.
This system is NOT confirmed compatible with 24V or 48V battery banks — DATA states 12V and 9-18V operating ranges only. This is NOT a starter battery. Standard lead-acid chargers are NOT recommended for the LiFePO4 cell; use a charger designed for lithium chemistry. Series/parallel expansion limits for the battery are NOT stated in the source data and should be confirmed before combining multiple units [NEEDS VERIFICATION].
FAQ
Q: What chemistry does the 12V HUSKY2 battery use?
A: It uses LiFePO4 (Lithium Iron Phosphate) chemistry, built with Tier 1 LFP cells.
Q: Does the HUSKY2 protect against cold-weather charging damage?
A: Yes. It includes a self-heating function for cold-weather charge protection.
Q: What is the operating voltage range of the Links2 Node 12 control system?
A: The Node 12 operates at 9-18V with a maximum input current of 80A.
Q: How many output channels does the Links2 Node 12 have?
A: It has four 30A output channels (including two H-Bridge sets) and eight 10A dimmable PWM channels.
Q: What size is the Vision 10 monitor screen?
A: The Vision 10 has a 10.1-inch display with 1024 x 600 resolution.
Warranty & Support
Warranty terms for this system are not included in the data provided here. Refer to the "Resources (System Manuals and Warranty)" Tab above for the manufacturer's full warranty documentation. If you have questions about this system before ordering, ask us — we always reply back.
