This is a wall-sleeve air conditioner with electric heat strip for hotel rooms, apartments, or additions where central ductwork isn't available. It's built for property managers and homeowners who need self-contained, per-room climate control on a standard 230/208V circuit.
This PMC073J25AXXX is a cooling-with-electric-heat PTAC (not a heat pump) built on the Amana PMC chassis, intended for hospitality guest rooms, multifamily units, and room additions where a self-contained through-wall system replaces central ductwork. It meets or exceeds ASHRAE 90.1 efficiency standards. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fit & Power Requirements
- Wall sleeve opening: industry-standard 42 in wide x 16-1/16 in high (rough framing opening approx. 42-1/4 in wide x 16-1/4 in minimum high).
- Voltage: 230/208V. Operating range 197V minimum to 253V maximum.
- Amperage: compressor draw 4.4/4.4A; total system amps with heat 11.2/10.1A; MCA 14.1A; MOP 15A.
- NEMA plug: 6-15P factory-installed power cord, shipped with LCDI device per UL 484 (applies to all units under 250V).
- Wall Sleeve is NOT included — order separately (e.g., WS900E, WS900QW, or an extra-deep/seacoast variant as the application requires).
- Exterior Architectural Grille is NOT included — order separately (SGK, AGK, or PGK series).
- Not compatible with 115V circuits.
- Not compatible with 265V circuits. The 265V commercial sibling of this chassis is model PMC074J, which requires a dedicated Amana sub-base or hardwire kit — this 230/208V cord-and-plug unit must not be substituted onto a 265V circuit.
- Not a drop-in fit for non-standard sleeve openings outside the 42 in x 16-1/16 in standard.
The most common callback on PTAC replacements is water staining under the sleeve, not an electrical fault. When you set the wall sleeve for this chassis, pitch it 1/4 bubble toward the outside wall using a torpedo level — level side-to-side, but with that slight outward slope, condensate drains off the base pan instead of migrating back into the wall cavity and soaking the drywall over a heating season. Confirm the sleeve still extends a minimum of 1/4 in beyond the exterior wall face before you seal it. On the electrical side, verify the receptacle is a matching NEMA 6-15R before you land the factory 6-15P cord — a mismatched receptacle gets forced or adapted in the field more often than it should, and that's an NEC receptacle-code violation and a warranty-voiding move, not just an inconvenience. Property managers doing multi-room turnovers should standardize sleeve pitch and receptacle type across the property to keep every unit swap a true drop-in.
Key Benefits
- EER of 12.7/12.8, meeting or exceeding ASHRAE 90.1 efficiency requirements.
- Fresh air intake adjustable from 25-35 CFM for make-up air ventilation without opening a window.
- Single-stage 2.5/2.1 kW electric heat strip supplies 8,500 BTU/h heating at 230V (6,800 BTU/h at 208V) as a companion to compressor cooling.
- Factory LCDI power cord (UL 484) reduces field wiring and speeds up plug-and-play installation on existing 230/208V receptacles.
- R-32 refrigerant.
- 342 CFM airflow for space cooling distribution.
Technical Table
| Spec | Value | Unit |
|---|---|---|
| Voltage | 230/208 | V |
| Cooling Capacity | 6,800/6,700 | BTU/h |
| Heating Capacity (230V) | 8,500 | BTU/h |
| Heating Capacity (208V) | 6,800 | BTU/h |
| Electric Heat Strip Size | 2.5/2.1 | kW |
| Heater Stages | 1 | - |
| Compressor Amps | 4.4/4.4 | A |
| Compressor Watts | 535/520 | W |
| EER | 12.7/12.8 | BTU/Wh |
| CFM | 342/342 | CFM |
| Fresh Air CFM | 25-35 | CFM |
| Total Watts with Heat | 2,570/2,115 | W |
| Total Amps with Heat | 11.2/10.1 | A |
| MCA | 14.1 | A |
| MOP | 15 | A |
| NEMA Plug Type | 6-15P | - |
| Power Cord / LCDI | 6-15P with LCDI device, UL 484 | - |
| Refrigerant Type | R-32 | - |
| Wall Sleeve Dimensions | Standard 42 x 16-1/16 | in |
| Wall Sleeve Included | Not Included | - |
| Exterior Architectural Grille Included | Not Included | - |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Compatible with 230/208V circuits via a factory-installed 6-15P plug into a matching NEMA 6-15R receptacle.
- Fits standard 42-inch x 16-1/16-inch wall sleeve openings, including WS900E and WS900QW sleeve models.
- Not compatible with 115V circuits.
- Not compatible with 265V circuits or applications; the 265V commercial sibling chassis is PMC074J and requires its own sub-base or hardwire kit.
- Wall Sleeve NOT included — must be purchased separately.
- Exterior Architectural Grille NOT included — must be purchased separately.
- Not a drop-in replacement for non-standard or custom sleeve openings.
Compliance & Environment Table
| Spec | Value |
|---|---|
| Refrigerant Type | R-32 |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Power Cord Compliance | LCDI device per UL 484 (units under 250V) |
| Voltage Operating Range | 197V minimum / 253V maximum (230/208V models) |
| Overcurrent Protection (no heater) | 15A for all units without electric heaters |
FAQ
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This unit is designed to install into an industry-standard 42 in wide x 16-1/16 in high wall sleeve opening, such as the WS900E or WS900QW series.
What breaker size and plug type does this unit require?
This unit ships with a factory-installed 6-15P power cord. Minimum circuit ampacity (MCA) is 14.1 amps, with a maximum overcurrent protection (MOP) rating of 15 amps.
Can this be hardwired for 265V commercial applications?
No. This is a 230/208V unit and is not rated for 265V. The 265V commercial sibling of this chassis is model PMC074J, which requires an Amana sub-base (PTSB4**E series) or hard-wire kit PTPWHWK4 with disconnect switch PSHW04A, along with factory-installed cartridge-style time-delay fuses. Do not attempt to wire this 230/208V unit into a 265V circuit.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
[NEEDS VERIFICATION] Exact installer-licensing requirements for warranty validity are not confirmed in the provided specification data. Refer to the warranty document in the Resources tab for exact terms.
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes. This chassis is built to the industry-standard 42 in x 16-1/16 in wall sleeve opening. It is not a drop-in fit for non-standard or custom sleeve openings.
Warranty & Registration
This unit carries a 1-Year Repair/Replace warranty and a 5-Year Parts Limited Warranty per the manufacturer's published badge terms. Exact coverage terms, including any distinctions between residential and commercial hospitality usage, are detailed in the warranty PDF located in the "Resources (System Manuals and Warranty)" Tab above — refer there before assuming coverage scope. If you have questions about what's covered before you order, ask us — we always reply back.
