This is a wall-sleeve air conditioner and electric heater built for hotel rooms, apartments, and additions near saltwater or coastal air where standard components corrode quickly. It's designed for property managers and homeowners who need self-contained, per-room climate control with added protection against seacoast corrosion.
The PTC154J35CXXX is a 265V packaged terminal air conditioner with a 3.7 kW electric heat strip, built on Amana's standard cooler chassis with feature code C seacoast corrosion protection for coastal and high-salinity environments. This configuration suits hospitality properties, coastal residential additions, and any application needing per-room cooling and supplemental electric heat without ductwork. All units meet or exceed ASHRAE 90.1. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fit & Power Requirements
- Wall sleeve opening: Industry-standard 42 in wide x 16-1/16 in high (sleeve sold separately - see Compatibility section).
- Voltage: 265V, operating range 239V minimum to 292V maximum.
- Amperage with 3.7 kW heater installed: 17.9A MCA, 20A MOP (Max Overcurrent Protection).
- Power cord/plug: NEMA 7-20P, factory-installed.
- Required for 265V operation: Amana sub-base (PTSB4**E series) or hard-wire kit PTPWHWK4 with disconnect switch PSHW04A - neither is included with this unit.
- Factory-installed cartridge-style time-delay fuses are required on all 265V models.
- Wall Sleeve is NOT included and must be ordered separately.
- Exterior Architectural Grille is NOT included and must be ordered separately.
- Not compatible with 115V circuits.
- Not compatible with 230/208V circuits - if you need a 230/208V version of this chassis, see sibling model PTC153J.
- This is a 265V unit; it does not use the LCDI power cord protection (LCDI applies only to units under 250V).
- Not a drop-in fit for non-standard or custom sleeve openings - verify sleeve model before ordering.
Pro-Installer Tip: Sub-Base Wiring and Sleeve Pitch on 265V Seacoast Jobs
The Technical Friction: On 265V hospitality installs, techs sometimes wire a standard PTAC sub-base without confirming it's the Amana PTSB4**E series rated for this voltage class, or they skip the disconnect switch (PSHW04A) that hard-wire installs require. On top of that, seacoast environments accelerate any moisture path that condensate mismanagement creates.
The Long-Term Prevention: Confirm the sub-base or hard-wire kit is rated for 265V before energizing the circuit, and torque the sleeve mounting so it pitches roughly 1/4 bubble toward the exterior. That pitch keeps condensate draining outward instead of migrating back into the wall cavity and drywall, which is the leading cause of hidden moisture damage in PTAC sleeves near coastal air.
The Expert Validation: Check level and pitch with a torpedo level set to the 1/4-bubble mark per the sleeve framing diagram, and verify the sub-base/hardwire kit part number against the NEMA/Amana compatibility chart before final connection.
The Professional Standard: Cartridge-style time-delay fuses are factory-installed on 265V models per code requirements - do not substitute standard fuses. This aligns with NEC overcurrent protection requirements and standard property-management commissioning checklists for commercial PTAC circuits.
Key Benefits
- 14,800 BTU/h cooling capacity rated at 10.7 EER for continuous per-room comfort control.
- 3.7 kW electric heat strip delivers 12,600 BTU/h of supplemental heat at 265V.
- 4.4 pints/hour dehumidification helps manage humidity in coastal and high-moisture climates.
- 65 CFM fresh air vent option supports make-up air in occupied hospitality rooms.
- Feature code C seacoast corrosion protection extends component life in salt-air environments.
- R-32 refrigerant chassis meets or exceeds ASHRAE 90.1 efficiency standards.
| Spec | Value | Unit |
|---|---|---|
| Cooling Capacity | 14,800 | BTU/h |
| Heating Capacity (265V, 3.7 kW heat) | 12,600 | BTU/h |
| EER | 10.7 | - |
| Electric Heat Strip Size | 3.7 | kW |
| Electric Heat Stages | 1 | stage |
| Voltage | 265 | V |
| Voltage Operating Range | 239-292 | V |
| Compressor Amps | 6.3 | A |
| Compressor Watts | 1,380 | W |
| MCA (No Heater) | 7.4 | A |
| Total Watts (With Heater) | 3,770 | W |
| Total Amps (With Heater) | 14.2 | A |
| MCA (With Heater) | 17.9 | A |
| MOP | 20 | A |
| NEMA Plug Type / Power Cord | 7-20P | - |
| CFM Wet (High/Low) | 400/314 | CFM |
| CFM Dry (High/Low) | 414/414 | CFM |
| Fresh Air Vent | 65 | CFM |
| Dehumidification | 4.4 | pints/hr |
| Net Weight | 113 | lb |
| Ship Weight | 130 | lb |
| Wall Sleeve Dimensions | Standard 42 x 16-1/16 | in |
| Wall Sleeve Included | Not Included | - |
| Exterior Architectural Grille Included | Not Included | - |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Fits industry-standard 42 in wide x 16-1/16 in high wall sleeve openings (WS900E, WS900QW, and seacoast-rated WS900SC are compatible sleeve families).
- Compatible with 265V dedicated circuits only, using the NEMA 7-20P power cord.
- Requires an Amana PTSB4**E sub-base or PTPWHWK4 hard-wire kit with PSHW04A disconnect switch for proper 265V installation - purchased separately.
- Not compatible with 115V circuits.
- Not compatible with 230/208V circuits - the 230/208V equivalent chassis is model PTC153J.
- Wall Sleeve NOT included - order separately.
- Exterior Architectural Grille NOT included - order separately.
- Not a drop-in replacement for non-standard or custom sleeve openings; verify sleeve dimensions before purchase.
| Compliance Item | Detail |
|---|---|
| Refrigerant Type | R-32 |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Overcurrent Protection (265V) | Cartridge-style time-delay fuses, factory-installed |
| Power Cord Standard | Not LCDI-equipped (LCDI applies only to units under 250V per UL 484) |
FAQ
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This unit fits the industry-standard 42 in x 16-1/16 in sleeve opening (e.g., WS900E, WS900QW, or the seacoast-rated WS900SC), but you need to order a compatible sleeve model separately.
What breaker size and plug type does this unit require?
With the 3.7 kW electric heat installed, this configuration requires a Minimum Circuit Ampacity (MCA) of 17.9A and Maximum Overcurrent Protection (MOP) of 20A. The unit ships with a 7-20P power cord for 265V circuits.
Can this be hardwired for 265V commercial applications?
Yes. This 265V model must be installed with an Amana brand sub-base (PTSB4**E series) or the hard-wire kit PTPWHWK4 paired with disconnect switch PSHW04A. Neither the sub-base nor the hard-wire kit is included with the unit.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
265V installations involve dedicated circuits, factory-installed cartridge-style time-delay fuses, and sub-base or hardwire kit wiring. Full manufacturer installation and warranty terms are provided in the Resources (System Manuals and Warranty) tab; consult the warranty PDF before installation.
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes, this chassis fits the industry-standard 42 in wide x 16-1/16 in high wall sleeve opening. It is not a drop-in fit for non-standard or custom sleeve openings without verifying compatibility first.
Warranty & Registration
This unit carries a manufacturer 1-Year Repair/Replace warranty and a 5-Year Parts Limited Warranty. Terms differ for commercial hospitality use versus residential use in some cases - exact conditions, exclusions, and registration steps are documented in the warranty PDF found in the Resources (System Manuals and Warranty) tab above. Review it before install, and ask us before you order if anything about coverage is unclear.
