This is a wall-sleeve air conditioner and electric heater built for hotel rooms, dormitories, and commercial additions running on a 265V electrical circuit. It's designed for property managers and facilities teams who need self-contained, per-room climate control and already have (or are installing) 265V wiring and a compatible sleeve.
The PTC154J35AXXX is a 265V PTAC chassis with a 1-stage 3.7 kW electric heat strip, suited to hospitality corridors and commercial additions already wired for 265V service. Refrigerant is R-32, and the unit is built to meet or exceed ASHRAE 90.1 efficiency standards. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
- Wall sleeve opening: Standard 42 in wide x 16-1/16 in high (fits WS900E / WS900QW sleeve family)
- Voltage: 265V — minimum 239V / maximum 292V operating range
- Total amps with heat: 14.2A; MCA 17.9A; MOP 20A
- NEMA plug type: 7-20P (20A power cord included)
- Wall Sleeve is NOT included and must be purchased separately.
- Exterior Architectural Grille is NOT included and must be purchased separately.
- Required for 265V operation: Amana sub-base (PTSB4**E series) or PTPWHWK4 hard-wire kit with PSHW04A disconnect switch — not included
- Not compatible with 115V circuits
- Not compatible with 230/208V circuits — for that voltage, see sibling model PTC153J (230/208V)
- Not a drop-in fit for non-standard or custom sleeve openings
On 265V hospitality retrofits, the recurring failure point is condensate management at the sleeve, not the electrical connection. Field crews often set the sleeve dead level because that "feels" correct, but PTAC sleeves need a deliberate pitch to the outside wall — roughly 1/4 bubble on a Torpedo Level — so condensate drains away from the unit instead of pooling and wicking into interior drywall. Left level or pitched inward, you'll see stained drywall and mold complaints within a season, even on a unit that's electrically perfect. Confirm pitch at rough-in, before drywall closes the opening, and verify against the framing diagram's rough-opening tolerance (42-1/4 in wide x 16-1/4 in minimum height). This is standard property-management best practice for multi-unit hospitality retrofits, where callbacks for water intrusion are far more common than callbacks for compressor failure.
- Compressor draws 6.3A at 1,380W independent of heat strip operation
- Dehumidification rate of 4.4 pints/hr at rated conditions
- Dedicated 65 CFM fresh-air ventilation setting
- Dual-speed wet/dry airflow (400/314 CFM wet, 414/414 CFM dry) for cooling and fan-only modes
- R-32 refrigerant, meets or exceeds ASHRAE 90.1
- Factory-installed cartridge-style time-delay fuses standard on all 265V models
| Spec | Value | Unit |
|---|---|---|
| Cooling Capacity | 14,800 | BTU/h |
| Heating Capacity (265V) | 12,600 | BTU/h |
| Electric Heat Strip Size | 3.7 | kW |
| Heat Stages | 1 | stage |
| EER | 10.7 | - |
| Voltage | 265 | V |
| Compressor Amps | 6.3 | A |
| Compressor Watts | 1,380 | W |
| Total Heater Watts | 3,770 | W |
| Total Amps (with heat) | 14.2 | A |
| MCA | 17.9 | A |
| MOP | 20 | A |
| NEMA Plug Type | 7-20P | - |
| CFM Wet (High/Low) | 400/314 | CFM |
| CFM Dry (High/Low) | 414/414 | CFM |
| Ventilation CFM | 65 | CFM |
| Dehumidification Rate | 4.4 | pints/hr |
| Net Weight | 113 | LBS |
| Ship Weight | 130 | LBS |
| Wall Sleeve Dimensions/Compatibility | Standard 42 x 16-1/16 | in |
| Wall Sleeve Included | Not Included | - |
| Exterior Architectural Grille Included | Not Included | - |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
- Fits industry-standard 42 in x 16-1/16 in wall sleeve openings (WS900E / WS900QW sleeve family)
- Compatible with 265V circuits within the 239V–292V operating range, using a 7-20P plug configuration
- Requires Amana sub-base (PTSB4**E series) or PTPWHWK4 hard-wire kit with PSHW04A disconnect for proper 265V installation — both sold separately
- Not compatible with 115V household circuits
- Not compatible with 230/208V circuits — that voltage is served by the sibling chassis PTC153J
- Wall Sleeve and Exterior Architectural Grille are sold separately in all cases
- Not a guaranteed fit for custom or non-standard sleeve depths without ordering the matching extra-deep sleeve variant
| Attribute | Value |
|---|---|
| Refrigerant Type | R-32 |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Electrical Cord Compliance | LCDI cord applies only to units under 250V — not applicable to this 265V configuration |
| Overcurrent Protection | Factory-installed cartridge-style time-delay fuses (required on 265V models) |
Frequently Asked Questions
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This unit is designed to fit a standard 42 in x 16-1/16 in sleeve opening (WS900E/WS900QW family), but the sleeve, drain kit, and exterior grille must be ordered separately.
What breaker size and plug type does this unit require?
This 265V configuration with the 3.7 kW electric heat strip requires a Minimum Circuit Ampacity (MCA) of 17.9A and Maximum Overcurrent Protection (MOP) of 20A. It ships with a 7-20P power cord.
Can this be hardwired for 265V commercial applications?
Yes. All 265V models must be installed with either an Amana sub-base (PTSB4**E series) or the PTPWHWK4 hard-wire kit paired with the PSHW04A disconnect switch. Neither is included with the unit and must be ordered separately. 265V models also require factory-installed, cartridge-style time-delay fuses.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
[NEEDS VERIFICATION] — installer licensing requirements for warranty validity are not stated in the provided specification data. Refer to the warranty document in the Resources tab for exact installation requirements.
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes, this chassis fits the industry-standard 42 in wide x 16-1/16 in high sleeve opening used by the WS900E and WS900QW sleeve families. It is not a drop-in fit for non-standard or custom-depth openings without the corresponding extra-deep sleeve variant.
This unit carries a 1-Year Repair/Replace warranty and a 5-Year Parts Limited Warranty on the sealed system, per manufacturer badge documentation. Commercial hospitality use terms may differ from residential terms. Exact coverage details, exclusions, and registration steps are set out in the warranty PDF — refer to the "Resources (System Manuals and Warranty)" Tab above on this page before ordering.
