HVAC Mirage | 12,000 BTU | 19.0 SEER2 | Wall Mounted | Single-Zone Mini Split System | 208-230V | IGFH091C

The HVAC Mirage IGFH091C is a 12,000 BTU wall-mounted indoor air handler engineered for single-zone comfort in bedrooms, living rooms, and home offices — delivering quiet, energy-efficient heating and cooling without the ductwork of a central system.

The HVAC Mirage IGFH091C wall-mounted indoor air handler delivers 12,000 BTU/h of inverter-driven cooling and heating capacity across a compact, low-profile form factor. Rated at 19.0 SEER2, it meets modern Department of Energy efficiency standards for residential ductless applications. This unit is designed to pair with a compatible HVAC Mirage outdoor condenser to form a complete single-zone mini split system — ideal for primary rooms requiring precise, zone-independent temperature control.

Indoor Air Handler

Outdoor Condenser
(Sold Separately)

Wireless Remote Control

Installation Requirements & Accessories

• Voltage: Requires a dedicated 208-230V / 60Hz / Single-Phase circuit. Not compatible with 115V-only circuits.
• Breaker Size: [NEEDS VERIFICATION] — consult installation manual or licensed electrician.
• Line Set Required (NOT Included): 3/8" OD liquid line and 7/8" OD suction line. Length determined by installation layout.
• Outdoor Condenser NOT Included: This listing is for the indoor air handler unit only. A compatible HVAC Mirage outdoor condenser must be purchased separately.
• Mounting Bracket NOT Included: A compatible wall mounting bracket must be sourced separately.
• Line Set NOT Included.
• Professional Installation Required: This is not a DIY system. EPA Section 608 certified technician required for refrigerant handling and system commissioning.

Pro-Installer Tip

When connecting the refrigerant lines to the HVAC Mirage IGFH091C, the most common field failure is an under-torqued or over-torqued flare fitting — both cause slow refrigerant leaks that eventually trigger an E1 communication error code and compressor short-cycling. Use an eccentric (offset) flaring tool to produce a consistent 45° flare seat on the copper tubing, then torque 3/8" flare nuts to 25–28 ft-lb and 7/8" flare nuts to 65–70 ft-lb with a calibrated digital torque wrench — never estimate by feel. Before opening the service valves, pull a system vacuum to below 300 microns and hold for a minimum of 15 minutes to confirm zero leak path and eliminate residual moisture that would otherwise acid-wash the electronic expansion valve (EEV). Per EPA Section 608, only a certified technician may recover, recycle, or charge R-410A refrigerant — improper venting is a federal violation and permanently voids the 7-year compressor warranty.

Key Benefits

• 19.0 SEER2 Efficiency: Meets current DOE minimum efficiency standards with room to reduce operating costs compared to legacy SEER-rated systems.
• 12,000 BTU (1.0 Ton) Capacity: Sized for spaces up to approximately 450–550 sq ft depending on insulation, ceiling height, and climate zone.
• R-410A Factory Pre-Charged: Refrigerant is sealed and charged at the factory, reducing the risk of field-introduced air or moisture contamination.
• 208-230V Single-Phase Operation: Standard residential voltage — works with the same circuit class as a central air conditioner or electric dryer.
• 7-Year Compressor / 5-Year Parts Warranty: Factory-backed coverage provides long-term reliability assurance when installed by a licensed professional.
• Wall-Mounted Form Factor: No ceiling penetration required; mounts high on an exterior or interior wall for optimal airflow distribution and minimal footprint.

Technical Specifications

Compatibility & Fitment

• ✅ Compatible with: Dedicated 208-230V single-phase, 60Hz residential and light-commercial electrical circuits.
• ✅ Compatible with: HVAC Mirage Series matched outdoor condenser units (verify AHRI-certified pair by model number before purchasing).
• ✅ Line set size: 3/8" OD liquid line x 7/8" OD suction line.
• ❌ Not compatible with 115V-only circuits — this unit requires 208-230V. Attempting to wire to a 115V circuit will damage the unit and void the warranty.
• ❌ Outdoor condenser NOT included — must be purchased separately. Do not assume compatibility with non-HVAC Mirage outdoor units without verifying AHRI certification.
• ❌ Line set NOT included — purchase a separately rated 3/8" x 7/8" line set in the appropriate length for your installation.
• ❌ Mounting bracket NOT included — a compatible wall mounting plate must be sourced separately.
• ❌ Not a DIY system — this unit is NOT pre-charged with quick-connect line set fittings. EPA Section 608 certified installation is required.

Frequently Asked Questions

What breaker size do I need for the HVAC Mirage IGFH091C?

The IGFH091C operates on a dedicated 208-230V single-phase, 60Hz circuit. The exact breaker amperage requirement is [NEEDS VERIFICATION] — consult the full installation manual or your licensed electrician before sizing the disconnect. Do not install on a shared or 115V-only circuit.

Is professional installation required to keep the warranty valid?

Yes. The HVAC Mirage IGFH091C is not a DIY kit. It does not include pre-charged line sets with quick-connect fittings. A licensed HVAC technician must perform the refrigerant line brazing or flaring, system evacuation, and commissioning. The factory warranty — 7-Year Compressor / 5-Year Parts Limited — is contingent on professional installation.

Is the line set included, and if not, what size do I need to buy?

The line set is NOT included. This listing is for the indoor air handler unit only. You will need to purchase a separate line set sized at 3/8" OD liquid line and 7/8" OD suction line. Line set length should be selected based on the distance between your indoor and outdoor units.

Does this unit require a matching outdoor condenser, and is one included?

An outdoor condenser unit is NOT included. The IGFH091C is an indoor air handler only. It must be paired with a compatible HVAC Mirage outdoor condenser unit. Verify the AHRI-certified matched combination before purchasing to ensure rated efficiency and warranty compliance.

What refrigerant does this system use, and is it pre-charged?

The IGFH091C uses R-454B refrigerant, which is factory pre-charged in the unit. However, because this is a non-DIY indoor handler (not a pre-charged line set kit), a licensed EPA Section 608 certified technician must handle all refrigerant connections, system evacuation, and charge verification during installation.

Compliance & Warranty

Factory Warranty: 7-Year Compressor / 5-Year Parts Limited Warranty. Warranty coverage requires installation by a licensed HVAC professional. DIY installation voids factory warranty terms.

Refrigerant Compliance: R-410A handling is regulated under EPA Section 608 of the Clean Air Act. Only EPA 608 certified technicians may purchase, handle, recover, or charge R-410A refrigerant. Venting refrigerant to atmosphere is a federal violation subject to civil penalties.

Efficiency Compliance: Rated at 19.0 SEER2, this unit meets the DOE's updated minimum efficiency standards effective January 1, 2023 for residential cooling equipment.