This is a wall-sleeve air conditioner and heater for hotel rooms, apartments, additions, or offices where central ductwork isn't available. It's built for property managers and homeowners who need self-contained, per-room climate control with electric heat backup.
The PMC153J35AXXX is a 230/208V packaged terminal air conditioner with electric heat, sized for hospitality rooms, additions, and multifamily units where a self-contained sleeve system replaces central ductwork. Cooling and heating performance figures reflect standard chassis testing per Amana's published catalog data, and all units meet or exceed ASHRAE 90.1. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fit & Power Requirements
- Wall sleeve opening: standard 42 in wide x 16-1/16 in high (standard depth 14 in) — Wall Sleeve NOT included, sold separately.
- Voltage: 230/208V. Operating range: minimum 197V / maximum 253V.
- Amperage: 19.5A minimum circuit ampacity (MCA); 20A maximum overcurrent protection (MOP).
- NEMA plug type: 6-20P. Ships with factory-installed LCDI power cord per UL 484 (applies to all units under 250V).
- Exterior Architectural Grille NOT included — order SGK, AGK, or PGK grille separately.
- Not compatible with 115V circuits.
- Not compatible with 265V circuits or the associated Amana sub-base/hard-wire kit hardware. The 265V commercial sibling of this chassis is model PMC154J — do not substitute this 230/208V unit into a 265V sleeve or receptacle.
- Not a drop-in replacement for non-standard or custom sleeve openings.
Key Benefits
- EER rating of 10.4/10.5 for the cooling-only chassis at 230V/208V, respectively.
- 412/412 CFM indoor airflow keeps room air circulation consistent across both voltage taps.
- Built-in fresh air ventilation control (25-35 CFM) for make-up air in tightly sealed rooms.
- Single-stage electric heat strip delivers 12,000 BTU heating at 230V or 9,900 BTU at 208V.
- R-32 refrigerant chassis, meeting or exceeding ASHRAE 90.1 efficiency standards.
- Factory LCDI power cord (UL 484) reduces field wiring work for standard voltage installs.
Technical Table
| Spec | Value | Unit |
|---|---|---|
| Cooling Capacity | 14,500/14,400 | BTU/h |
| Heating Capacity (230V) | 12,000 | BTU/h |
| Heating Capacity (208V) | 9,900 | BTU/h |
| Electric Heat Size | 3.5/3.0 | kW |
| Heating Stages | 1 | stage |
| Voltage | 230/208 | V |
| Compressor Amps | 8.1/8.1 | A |
| Compressor Watts | 1,390/1,370 | W |
| EER | 10.4/10.5 | BTU/Wh |
| Total Heater Watts | 3,570/2,935 | W |
| Total Heater Amps | 15.5/14.1 | A |
| Minimum Circuit Ampacity (MCA) | 19.5 | A |
| Maximum Overcurrent Protection (MOP) | 20 | A |
| NEMA Plug Type | 6-20P | — |
| Indoor Airflow | 412/412 | CFM |
| Fresh Air Ventilation | 25-35 | CFM |
| Wall Sleeve Dimensions | 42 x 16-1/16 | in |
| Wall Sleeve Included | Not Included | — |
| Exterior Grille Included | Not Included | — |
| Refrigerant | R-32 | — |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Compatible with 230/208V circuits via NEMA 6-20P plug and 20A dedicated breaker.
- Fits standard 42-inch x 16-1/16-inch wall sleeve openings (standard depth 14 in) — compatible with WS900E, WS900QW, and related standard-depth Amana sleeve models.
- Not compatible with 115V circuits.
- Not compatible with 265V circuits or the Amana sub-base/hard-wire kit hardware used on the PMC154J commercial sibling chassis.
- Wall Sleeve NOT included — must be purchased separately.
- Exterior Architectural Grille NOT included — must be purchased separately.
- Not a drop-in fit for custom or non-standard sleeve openings outside the 42 in x 16-1/16 in standard.
Compliance & Environment
| Attribute | Detail |
|---|---|
| Refrigerant Type | R-32 |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Power Cord Compliance | LCDI power cord, UL 484 (units under 250V) |
| Voltage Operating Range | 197V minimum / 253V maximum |
FAQ
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This PTAC installs into a standard 42 in wide x 16-1/16 in high sleeve, but the chassis, sleeve, and exterior grille are three separate purchases.
What breaker size and plug type does this unit require?
This configuration requires a 20-amp circuit (MOP) with a minimum circuit ampacity of 19.5A, using a NEMA 6-20P plug. It ships with a factory LCDI power cord per UL 484, since it operates under 250V.
Can this be hardwired for 265V commercial applications?
No. This is a 230/208V model. It is not rated for 265V circuits and does not use the Amana sub-base or hard-wire kit required for 265V installs. The 265V commercial version of this chassis is sold as model PMC154J.
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes. This chassis fits the industry-standard 42 in wide x 16-1/16 in high wall sleeve opening, with a rough framing opening of approximately 42-1/4 in wide x 16-1/4 in minimum high. It is not designed for non-standard or custom sleeve openings.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
The unit's electrical rating (20A circuit, 6-20P plug, 19.5A MCA) means it should be installed on a matched dedicated circuit. [NEEDS VERIFICATION - exact installer-licensing warranty language is in the manufacturer warranty PDF, not confirmed in the provided catalog data.]
Warranty & Registration
This unit carries a 1-Year Repair/Replace warranty and a 5-Year Parts Limited Warranty on covered components, per Amana's published warranty badge terms. Exact coverage details, commercial-versus-residential usage limits, and registration requirements are set out in the manufacturer warranty document. Refer to the "Resources (System Manuals and Warranty)" Tab above on this page for the full warranty PDF before installation, especially if this unit will see hospitality or other commercial-duty use.
