This is a wall-sleeve air conditioner and heater for hotel rooms, apartments, additions, or other spaces where central ductwork isn't available. It's built for property managers and homeowners who need self-contained, per-room climate control with electric-resistance backup heat.
The PMC153J50AXXX is a 230/208V packaged terminal air conditioner with a 5.0/4.1 kW electric heat strip, built for hospitality rooms, additions, and multi-family units where a wall sleeve replaces central ductwork. This unit meets or exceeds ASHRAE 90.1 efficiency standards. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fit & Power Requirements
- Wall sleeve opening: Standard industry 42 in wide x 16-1/16 in high (fits WS900E / WS900QW series sleeves)
- Voltage: 230/208V — minimum 197V / maximum 253V per manufacturer voltage limits
- Total amps with heat: 22.1/20.0A; MCA 27.6A; MOP 30A
- NEMA plug type: 6-30P, factory-installed cord with LCDI device per UL 484 (applies to all units under 250V)
- Wall Sleeve is NOT included — sold separately.
- Exterior Architectural Grille is NOT included — sold separately.
- Not compatible with 115V circuits
- Not a 265V unit: does not require and is not compatible with the 265V-only Amana sub-base (PTSB4**E) or hard-wire kit PTPWHWK4/disconnect PSHW04A — those apply only to the 265V commercial sibling, model PMC154J
- Not a drop-in fit for non-standard or custom sleeve openings
Key Benefits
- 1-stage electric heat backup rated 5.0 kW at 230V / 4.1 kW at 208V for supplemental warmth alongside compressor heating limits
- EER of 10.4/10.5 for cooling efficiency at rated voltage
- 412/412 CFM indoor airflow across cooling and heating modes
- 25-35 CFM of fresh air ventilation for make-up air in tightly sealed rooms
- R-32 refrigerant, a lower-GWP option compared to legacy refrigerants
- Meets or exceeds ASHRAE 90.1 efficiency standards
Technical Table
| Spec | Value | Unit |
|---|---|---|
| Cooling Capacity | 14,500/14,400 | BTU/h |
| Heating Capacity (230V) | 17,100 | BTU/h |
| Heating Capacity (208V) | 14,000 | BTU/h |
| Electric Heat Strip Size | 5.0/4.1 | kW |
| EER | 10.4/10.5 | — |
| Voltage | 230/208 | V |
| Compressor Amps | 8.1/8.1 | A |
| Compressor Watts | 1,390/1,370 | W |
| Total Heater Watts | 5,070/4,160 | W |
| Total Amps (with Heat) | 22.1/20.0 | A |
| MCA | 27.6 | A |
| MOP | 30 | A |
| NEMA Plug Type | 6-30P | — |
| Indoor CFM | 412/412 | CFM |
| Fresh Air CFM | 25-35 | CFM |
| Refrigerant Type | R-32 | — |
| Wall Sleeve Dimensions | Standard 42 x 16-1/16 | in |
| Wall Sleeve Included | Not Included | — |
| Exterior Grille Included | Not Included | — |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Compatible with 230/208V circuits via NEMA 6-30P plug, factory cord with LCDI device (UL 484)
- Fits standard 42-inch x 16-1/16-inch wall sleeve openings (WS900E / WS900QW sleeve series)
- Not compatible with 115V circuits
- Not compatible with 265V hardwire-only setups — this is a 230/208V model, not the 265V sibling PMC154J
- Wall Sleeve NOT included — must be ordered separately
- Exterior Architectural Grille NOT included — must be ordered separately
- Not a drop-in replacement for non-standard or custom sleeve openings
Compliance & Environment
| Item | Detail |
|---|---|
| Refrigerant Type | R-32 |
| Electrical Compliance | Factory-installed LCDI power cord per UL 484 (units under 250V) |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Voltage Operating Range | 197V minimum / 253V maximum |
FAQ
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This unit is designed to fit the industry-standard 42 in x 16-1/16 in sleeve opening (WS900E / WS900QW series), but the sleeve itself is not included with the PTAC unit.
What breaker size and plug type does this unit require?
This configuration has a Minimum Circuit Ampacity (MCA) of 27.6 amps and requires a Maximum Overcurrent Protection (MOP) of 30 amps. It ships with a factory-installed NEMA 6-30P power cord and LCDI device per UL 484.
Can this be hardwired for 265V commercial applications?
No. This is a 230/208V model, not a 265V unit. It is not compatible with 265V circuits and does not use the Amana sub-base (PTSB4**E) or hard-wire kit (PTPWHWK4) required for 265V installations. For a 265V commercial version of this chassis, see model PMC154J.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
[NEEDS VERIFICATION] Exact installer-licensing requirements for warranty validity are detailed in the manufacturer warranty document. Refer to the "Resources (System Manuals and Warranty)" Tab above for full terms.
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes. This chassis fits the industry-standard 42 in wide x 16-1/16 in high sleeve opening used by the WS900E and WS900QW sleeve series. It is not a drop-in fit for non-standard or custom sleeve openings.
Warranty & Registration
This unit carries a 1-Year Repair/Replace warranty and a 5-Year Parts Limited Warranty on the sealed system, per manufacturer badge documentation. Commercial hospitality usage and residential usage limits, along with full registration terms, are detailed in the warranty PDF. Refer to the "Resources (System Manuals and Warranty)" Tab above for the exact terms before ordering. Ask us before you order if you're unsure which warranty tier applies to your property type — we always reply back.
