This is a wall-sleeve air conditioner and electric-heat unit for hotel rooms, apartments, additions, or any space without central ductwork. It's built for property managers and homeowners who need self-contained, per-room cooling and heating on a standard 230/208V circuit.
The PTC093J35AXXX is a standard-model PTAC built on Amana's PTC chassis, pairing R-32 refrigerant cooling with a 3.5/3.0 kW electric heat strip for spaces without central ductwork — common in hotel rooms, multifamily units, and additions. Performance is rated per AHRI methodology as reflected in the manufacturer catalog data, and the unit meets or exceeds ASHRAE 90.1 efficiency requirements. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fit & Power Requirements
- Wall sleeve opening: industry-standard 42 in wide x 16-1/16 in high (matches Amana WS900E / WS900QW sleeve series).
- Voltage: 230/208V. Compressor draws 4.1/4.1A; with electric heat engaged, total draw is 15.5/14.1A.
- Circuit requirement: MCA 19.5A, MOP (breaker size) 20A, NEMA 6-20P plug on the factory power cord.
- Factory-installed LCDI power cord per UL 484 (applies to all units under 250V, including this one).
- Wall Sleeve is NOT included and must be ordered separately.
- Exterior Architectural Grille is NOT included and must be ordered separately.
- Not compatible with 115V circuits.
- Not compatible with 265V hardwire-only installations — that voltage class is served by the PTC094J commercial sibling, which requires an Amana sub-base or hard-wire kit.
- Not a drop-in fit for non-standard or custom sleeve openings.
Matching the NEMA 6-20P plug to the correct 20A/230-208V receptacle is the most common point of failure on retrofit jobs — a mismatched receptacle either won't accept the cord or gets force-fit into an incompatible outlet, risking arcing at the blades. Before terminating the receptacle, verify configuration against a NEMA Receptacle Chart, not by eye. Beyond the plug, set the wall sleeve with a slight outward pitch — about 1/4 bubble on a Torpedo Level — so condensate drains to the exterior grille instead of pooling against the interior drywall. Skipping this pitch check is the leading cause of hidden water damage behind PTAC sleeves in hospitality retrofits. Document the receptacle type and sleeve pitch on the work order; many property management standards and local NEC receptacle code inspections require this record before a unit is signed off for occupancy.
Key Benefits
- EER of 12.1/12.2 for efficient per-room cooling on a standard 230/208V circuit.
- 2 pints/hour of dehumidification to help manage humidity in guest rooms and living spaces.
- 65 CFM fresh air vent for make-up air without opening a window.
- Single-stage 3.5/3.0 kW electric heat strip delivers 12,000/9,900 BTU/h of supplemental heat.
- R-32 refrigerant, a lower-GWP option relative to older refrigerants.
- Meets or exceeds ASHRAE 90.1 efficiency requirements.
| Spec | Value | Unit |
|---|---|---|
| Cooling Capacity (230V/208V) | 9,200/9,000 | BTU/h |
| Heating Capacity (230V/208V) | 12,000/9,900 | BTU/h |
| Electric Heat Strip Size | 3.5/3.0 | kW |
| Heater Stages | 1 | stage |
| Voltage | 230/208 | V |
| Compressor Amps | 4.1/4.1 | A |
| Compressor Watts | 760/750 | W |
| Total Watts (with heat) | 3,570/2,935 | W |
| Total Amps (with heat) | 15.5/14.1 | A |
| MCA | 19.5 | A |
| MOP (Breaker Size) | 20 | A |
| NEMA Plug Type | 6-20P | - |
| EER | 12.1/12.2 | BTU/Wh |
| Dehumidification | 2 | pints/hr |
| CFM Wet (High/Low) | 290/264 | CFM |
| CFM Dry (High/Low) | 321/295 | CFM |
| Fresh Air Vent | 65 | CFM |
| Net Weight | 102 | lb |
| Shipping Weight | 117 | lb |
| Refrigerant | R-32 | - |
| Wall Sleeve Compatibility | Standard 42 x 16-1/16 | in |
| Wall Sleeve Included | Not Included | - |
| Exterior Architectural Grille Included | Not Included | - |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Compatible with 230/208V circuits via a NEMA 6-20P plug and matching 20A receptacle.
- Fits industry-standard 42 in x 16-1/16 in wall sleeve openings (Amana WS900E / WS900QW series and compatible sleeves).
- Not compatible with 115V circuits.
- Not suitable for 265V hardwire-only applications — see the PTC094J (265V commercial sibling), which requires an Amana sub-base (PTSB4**E series) or hard-wire kit PTPWHWK4 with disconnect PSHW04A.
- Wall Sleeve NOT included — order separately.
- Exterior Architectural Grille NOT included — order separately.
- Not a drop-in replacement for non-standard or custom sleeve openings.
Compliance & Environment
| Spec | Value |
|---|---|
| Refrigerant Type | R-32 |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Power Cord Compliance | Factory-installed LCDI power cord per UL 484 (units under 250V) |
| Voltage Operating Range | Min 197V / Max 253V (230/208V models) |
FAQ
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This unit fits the industry-standard 42 in x 16-1/16 in wall sleeve opening (e.g., Amana WS900E / WS900QW sleeve series), but the sleeve and exterior architectural grille must be ordered independently.
What breaker size and plug type does this unit require?
This configuration (3.5/3.0 kW heat) requires a 20-amp circuit (MOP) with an MCA of 19.5A, using a NEMA 6-20P plug on the factory-installed power cord.
Can this be hardwired for 265V commercial applications?
No. This unit is rated 230/208V only. It is not compatible with 265V circuits. The 265V commercial version of this chassis is the PTC094J, which requires an Amana sub-base (PTSB4**E series) or hard-wire kit PTPWHWK4 with disconnect switch PSHW04A, none of which are included or applicable here.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
Consult the manufacturer warranty document in the Resources tab for exact installation and licensing requirements before installing. This listing does not assert specific licensing terms beyond what the warranty PDF states.
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes. This chassis is designed for the industry-standard 42 in wide x 16-1/16 in high wall sleeve opening. It is not a drop-in fit for non-standard or custom sleeve dimensions without verification.
Warranty & Registration
This unit carries a 1-Year Repair/Replace warranty and a 5-Year Parts Limited Warranty per the manufacturer's published warranty badge terms. Commercial hospitality use and residential use may carry different terms or limitations — refer to the full Product Warranty PDF in the "Resources (System Manuals and Warranty)" Tab above for exact coverage, exclusions, and registration steps before installation.
