This is a wall-sleeve air conditioner and electric-heat unit built for hotel rooms, apartments, or additions near saltwater exposure where central ductwork isn't available. It's suited to property managers and homeowners who need self-contained, per-room climate control with added protection against coastal corrosion.
The PTC093J35CXXX is a 9,200 BTU packaged terminal air conditioner with a 3.5/3.0 kW electric heat strip, built on Amana's PTC chassis with factory Seacoast corrosion protection for coastal hospitality and residential properties. All units meet or exceed ASHRAE 90.1. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fit & Power Requirements
- Wall sleeve opening: Standard 42 in wide x 16-1/16 in high (industry-standard PTAC sleeve dimension).
- Voltage: 230/208V. Not compatible with 115V circuits.
- Amperage with electric heat: 15.5/14.1A total; MCA 19.5A; MOP (breaker) 20A.
- Plug/cord: NEMA 6-20P power cord, factory-supplied, LCDI-equipped per UL 484 (applies to all units under 250V).
- Wall Sleeve is NOT included and must be ordered separately (e.g., WS900E, WS900QW, or WS900SC for full seacoast triple protection).
- Exterior Architectural Grille is NOT included and must be ordered separately (SGK, AGK, or PGK series).
- Not suitable for hardwire-only 265V applications. The 265V commercial sibling of this chassis is PTC094J, which requires an Amana sub-base (PTSB4**E) or hard-wire kit PTPWHWK4 with disconnect switch PSHW04A (sold separately).
- Not a drop-in replacement for non-standard or custom sleeve openings.
Key Benefits
- 9,200/9,000 BTU cooling (230V/208V) with EER 12.1/12.2 for efficient per-room operation.
- 3.5/3.0 kW electric heat strip delivers 12,000/9,900 BTU of supplemental heat in the same chassis.
- 2 pints/hr dehumidification helps manage humidity in guest rooms and living spaces.
- 65 CFM fresh air vent supports make-up air exchange without a separate ventilation system.
- Seacoast corrosion protection (Feature Code C) is built for coastal and high-salt-exposure environments.
- R-32 refrigerant chassis meets or exceeds ASHRAE 90.1 efficiency standards.
| Spec | Value | Unit |
|---|---|---|
| Cooling Capacity (230V/208V) | 9,200/9,000 | BTU/h |
| Heating Capacity (230V/208V) | 12,000/9,900 | BTU/h |
| Electric Heat Strip Size | 3.5/3.0 | kW |
| Heater Stages | 1 | — |
| EER | 12.1/12.2 | — |
| Voltage | 230/208 | V |
| Compressor Amps | 4.1/4.1 | A |
| Compressor Watts | 760/750 | W |
| Total Watts (w/ Heat) | 3,570/2,935 | W |
| Total Amps (w/ Heat) | 15.5/14.1 | A |
| MCA | 19.5 | A |
| MOP (Breaker) | 20 | A |
| NEMA Plug Type | 6-20P | — |
| CFM Wet (High/Low) | 290/264 | CFM |
| CFM Dry (High/Low) | 321/295 | CFM |
| Fresh Air Vent | 65 | CFM |
| Dehumidification | 2 | pints/hr |
| Net Weight | 102 | lb |
| Ship Weight | 117 | lb |
| Wall Sleeve Dimensions | Standard 42 x 16-1/16 | in |
| Wall Sleeve Included | Not Included | — |
| Exterior Architectural Grille Included | Not Included | — |
| Corrosion Protection | Seacoast Protected | — |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Fits the industry-standard 42 in x 16-1/16 in wall sleeve opening.
- Compatible with 230/208V circuits via NEMA 6-20P plug.
- Not compatible with 115V circuits.
- Not suitable for hardwire-only 265V applications; the 265V commercial sibling PTC094J requires an Amana sub-base (PTSB4**E) or hard-wire kit PTPWHWK4 with disconnect PSHW04A (sold separately).
- Wall Sleeve NOT included — order separately (WS900E, WS900QW, or WS900SC for seacoast protection).
- Exterior Architectural Grille NOT included — order separately (SGK, AGK, or PGK series).
- Not a drop-in replacement for non-standard or custom sleeve openings.
| Compliance/Environmental Attribute | Value |
|---|---|
| Refrigerant Type | R-32 |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Power Cord Compliance | LCDI power cord per UL 484 (units under 250V) |
| Voltage Operating Range | 197V min / 253V max (230/208V models) |
FAQ
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This chassis fits the industry-standard 42-inch by 16-1/16-inch wall sleeve opening (e.g., WS900E, WS900QW, or WS900SC seacoast-protected sleeve).
What breaker size and plug type does this unit require?
This 230/208V configuration with 3.5/3.0 kW electric heat requires a 20-amp circuit (MOP 20A, MCA 19.5A) and uses a NEMA 6-20P power cord.
Can this be hardwired for 265V commercial applications?
No. This model is rated 230/208V only and is not compatible with 265V circuits. The 265V commercial sibling of this chassis is PTC094J, which requires an Amana sub-base (PTSB4**E series) or hard-wire kit PTPWHWK4 with disconnect PSHW04A (not included) and factory-installed cartridge-style time-delay fuses.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
Exact installation and warranty conditions are detailed in the manufacturer warranty document. Refer to the "Resources (System Manuals and Warranty)" Tab above for full terms.
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes. This chassis is designed for the industry-standard 42-inch by 16-1/16-inch wall sleeve opening. It is not a drop-in fit for non-standard or custom sleeve openings.
Warranty & Registration
Manufacturer warranty coverage documented in source materials includes 1-Year Repair/Replace and 5-Year Parts Limited Warranty. Commercial hospitality use and residential use may carry different terms and conditions. Exact language, exclusions, and registration requirements are set out in the manufacturer warranty document. Refer to the "Resources (System Manuals and Warranty)" Tab above on this page for the full warranty text before you order — ask us if anything in that document is unclear.
