This is a wall-sleeve air conditioner and electric-heat unit for hotel rooms, apartments, coastal properties, or additions where central ductwork isn't available. It's built for property managers and homeowners who need self-contained, per-room climate control with added protection against salt-air corrosion.
The PTC153J25CXXX is a standard-cooler PTAC with a 2.5/2.1 kW electric heat strip, built on Amana's PTC153J chassis with seacoast corrosion protection (feature code C) for coastal hospitality and residential installs. This configuration is suited to hotel rooms, motels, extended-stay units, and additions where per-room electric heat and cooling replace central ductwork. All units meet or exceed ASHRAE 90.1. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fit & Power Requirements
- Wall sleeve opening: industry-standard 42 in wide x 16-1/16 in high (fits Amana WS900E, WS900QW, WS900SC seacoast sleeve, and compatible deep/heavy-gauge variants).
- Voltage: 230/208V. Minimum 197V / maximum 253V per Amana voltage-range specification.
- Electric heat: 2.5/2.1 kW, single stage. MCA 14.1A, MOP 15A, total amps 11.2/10.1A.
- Power cord: NEMA 6-15P, factory-installed, with LCDI device per UL 484 (applies to all units under 250V).
- Wall Sleeve and Exterior Architectural Grille are NOT included and must be ordered separately.
- Not compatible with 115V circuits.
- Not compatible with 265V hardwire installations. The 265V commercial sibling of this chassis is the Amana PTC154J, which requires a dedicated sub-base (PTSB4**E series) or hard-wire kit PTPWHWK4 with disconnect switch PSHW04A — none of that applies to this 230/208V unit.
- Not a drop-in fit for non-standard or custom sleeve openings outside 42 in x 16-1/16 in.
Wall sleeves for PTAC units are notorious for reverse pitch on retrofit jobs, especially when a mason levels the rough opening to the interior floor line instead of the sleeve itself. Set the sleeve level side-to-side and pitched approximately 1/4 bubble toward the outside wall — check it with a torpedo level before securing, not after. Skipping this step lets condensate migrate back into the wall cavity and rot the drywall or subfloor over a heating season, which is a callback that costs far more than the five minutes it takes to verify. This matches Amana's framing guidance for a rough opening of roughly 42-1/4 in wide by 16-1/4 in minimum high, with the sleeve extending at least 1/4 in beyond the exterior wall face. For any property with more than a handful of units, log the pitch check in your install QA sheet — it is standard practice in multi-family and hospitality PM programs for exactly this reason.
Key Benefits
- 2.5/2.1 kW electric heat strip provides supplemental heating without a heat pump compressor — suited to moderate climates where electric resistance heat is the standard.
- 4.4 pints/hr dehumidification helps manage humidity in guest rooms and coastal properties prone to moisture load.
- 65 CFM fresh air vent allows make-up air exchange without opening a window.
- Seacoast corrosion protection (feature code C) targets salt-air environments where standard-coil PTACs degrade faster.
- R-32 refrigerant.
- EER of 10.3/10.4 at 230V/208V respectively.
Technical Table
| Spec | Value | Unit |
|---|---|---|
| Cooling Capacity (230V/208V) | 14,800/14,500 | BTU/h |
| Heating Capacity (230V) | 8,500 | BTU/h |
| Heating Capacity (208V) | 6,800 | BTU/h |
| Electric Heat Size | 2.5/2.1 | kW |
| EER (230V/208V) | 10.3/10.4 | BTU/W |
| Voltage | 230/208 | V |
| Compressor Amps | 7.1/7.1 | A |
| Compressor Watts | 1,435/1,430 | W |
| Heater Total Watts | 2,570/2,115 | W |
| Heater Total Amps | 11.2/10.1 | A |
| MCA (with heater) | 14.1 | A |
| MOP | 15 | A |
| NEMA Plug Type | 6-15P | - |
| CFM Wet (High/Low) | 400/314 | CFM |
| CFM Dry (High/Low) | 412/390 | CFM |
| Fresh Air Vent CFM | 65 | CFM |
| Dehumidification | 4.4 | pints/hr |
| Net Weight | 113 | LB |
| Ship Weight | 130 | LB |
| Refrigerant Type | R-32 | - |
| Wall Sleeve Dimensions | 42 x 16-1/16 (Standard) | in |
| Wall Sleeve Included | Not Included | - |
| Exterior Architectural Grille | Not Included | - |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Compatible with 230/208V circuits via NEMA 6-15P plug, within the 197V–253V operating range.
- Fits the industry-standard 42 in x 16-1/16 in wall sleeve opening, including Amana WS900E, WS900QW, and the WS900SC seacoast-protected sleeve.
- Not compatible with 115V circuits.
- Not compatible with 265V hardwire-only applications — see the PTC154J commercial sibling and its required PTSB4**E sub-base or PTPWHWK4 hard-wire kit with PSHW04A disconnect.
- Wall Sleeve NOT included — order separately.
- Exterior Architectural Grille NOT included — order separately (SGK, AGK, or PGK series).
- Not a drop-in replacement for non-standard or custom sleeve openings.
Compliance & Environment
| Item | Detail |
|---|---|
| Refrigerant Type | R-32 |
| Overcurrent Protection (no heater) | 15A for all units without electric heaters |
| Power Cord / LCDI Compliance | Factory 6-15P cord with LCDI device per UL 484 (units under 250V) |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Voltage Operating Range | 197V minimum / 253V maximum (230/208V models) |
FAQ
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This unit fits the industry-standard 42 in x 16-1/16 in wall sleeve opening (e.g., Amana WS900E, WS900QW, or the WS900SC seacoast-triple-protected sleeve), but the sleeve and exterior grille must be ordered separately.
What breaker size and plug type does this unit require?
This configuration (2.5/2.1 kW electric heat at 230/208V) has an MCA of 14.1A and requires a 15A maximum overcurrent protection device. It ships with a factory-installed 6-15P power cord with an LCDI device per UL 484.
Can this be hardwired for 265V commercial applications?
No. This model is rated 230/208V only and is not compatible with 265V circuits. The 265V commercial version of this chassis is the Amana PTC154J, which requires a dedicated Amana sub-base (PTSB4**E series) or hard-wire kit PTPWHWK4 with disconnect switch PSHW04A.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
[NEEDS VERIFICATION] — installation labor requirements for warranty validity are not specified in the provided data. Refer to the warranty document in the Resources tab for exact terms.
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes. This chassis is designed for the industry-standard 42 in wide x 16-1/16 in high wall sleeve opening. It is not a drop-in fit for non-standard or custom sleeve openings.
Warranty & Registration
Based on manufacturer badge assets, this unit carries a 1-Year Repair/Replace warranty and a 5-Year Parts Limited Warranty. Exact terms — including any distinction between residential and commercial/hospitality usage — are detailed in the warranty PDF under the "Resources (System Manuals and Warranty)" Tab above. Ask us before you order if you need the full warranty language confirmed for a commercial hospitality deployment; we always reply back.
