This is a wall-sleeve air conditioner and electric-heat unit for hotel rooms, apartments, or additions where central ductwork isn't available. It's built for property managers and homeowners in seacoast or high-corrosion environments who need self-contained, per-room climate control with added protection against salt-air degradation.
The PTC153J50CXXX is a packaged terminal air conditioner with electric heat, built on Amana's PTC standard-cooler chassis and finished with seacoast corrosion protection for coastal hospitality and residential properties. This configuration pairs a 14,800/14,500 BTU cooling chassis with a 5.0/4.1 kW electric heat strip, delivering 17,100 BTU of heat at 230V (14,000 BTU at 208V). All units meet or exceed ASHRAE 90.1. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
- Wall sleeve opening: Standard 42 in wide x 16-1/16 in high (industry standard) — Wall Sleeve is NOT included and must be ordered separately (e.g., WS900E, WS900QW, or the seacoast-rated WS900SC).
- Exterior Architectural Grille is NOT included — select from SGK (stamped), AGK (extruded aluminum), or PGK (polymer) grille kits separately.
- Voltage: 230/208V. Amperage with heater installed: 22.1/20.0 total amps; MCA 27.6A; MOP 30A.
- Plug/Cord: Factory-installed NEMA 6-30P power cord with LCDI device per UL 484 (applies to all units under 250V).
- Not compatible with 115V circuits.
- Not compatible with 265V hardwire installations. The 265V commercial sibling chassis is the PTC154J, which requires an Amana sub-base (PTSB4**E series) or hard-wire kit PTPWHWK4 with disconnect switch PSHW04A — none of that hardware applies to or ships with this 230/208V unit.
- Not a drop-in fit for non-standard or custom sleeve openings outside 42 in x 16-1/16 in.
The most common callback on seacoast PTAC installs isn't the compressor — it's condensate finding its way into the drywall around the sleeve. A 42 in x 16-1/16 in opening gives you very little margin for error on pitch. Set the sleeve level side-to-side, then pitch it toward the outside wall by roughly 1/4 bubble on a torpedo level, matching Amana's framing diagram guidance. That slope routes condensate out through the base pan and drain, not backward into the room-side wall cavity. On coastal properties, pair this with the seacoast-rated grille and sleeve options (WS900SC) rather than standard steel — salt-laden air accelerates corrosion at fastener points long before the chassis itself fails. Confirm the receptacle is a NEMA 6-30 configuration before rough-in; a mismatched plug on a 27.6A MCA circuit is both a warranty voider and an NEC receptacle-code violation waiting for an inspector to find.
- Fresh air ventilation: 65 CFM vent rating for makeup air in occupied spaces.
- Dehumidification: 4.4 pints per hour of moisture removal at rated conditions.
- EER of 10.3/10.4 (230V/208V) for the cooling chassis.
- Single-stage 5.0/4.1 kW electric heat strip delivers supplemental heat without a heat pump compressor cycle.
- R-32 refrigerant charge.
- Seacoast corrosion protection (Feature Code C) for extended service life in coastal salt-air environments.
| Spec | Value | Unit |
|---|---|---|
| Cooling Capacity | 14,800/14,500 | BTU/h |
| EER | 10.3/10.4 | — |
| Compressor Amps | 7.1/7.1 | A |
| Compressor Watts | 1,435/1,430 | W |
| MCA (Chassis, No Heater) | 8.5 | A |
| CFM Wet (High/Low) | 400/314 | CFM |
| CFM Dry (High/Low) | 412/390 | CFM |
| Fresh Air Vent | 65 | CFM |
| Dehumidification | 4.4 | pints/hr |
| Net Weight | 113 | lb |
| Ship Weight | 130 | lb |
| Electric Heat Size | 5.0/4.1 | kW |
| Heat Stages | 1 | — |
| Heating Capacity (230V) | 17,100 | BTU/h |
| Heating Capacity (208V) | 14,000 | BTU/h |
| Heater Total Watts | 5,070/4,160 | W |
| Heater Total Amps | 22.1/20.0 | A |
| MCA (With Heater) | 27.6 | A |
| MOP | 30 | A |
| Voltage | 230/208 | V |
| NEMA Plug Type | 6-30P | — |
| Wall Sleeve Dimensions | 42 x 16-1/16 | in |
| Wall Sleeve Included | Not Included | — |
| Exterior Grille Included | Not Included | — |
| Refrigerant | R-32 | — |
| Corrosion Protection | Seacoast Protected | — |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
- Compatible with 230/208V circuits via a factory NEMA 6-30P plug.
- Fits standard 42 in x 16-1/16 in wall sleeve openings (e.g., WS900E, WS900QW, WS900SC).
- Seacoast corrosion protection matches coastal-grade sleeve/grille options such as WS900SC for full-system salt-air durability.
- Not compatible with 115V circuits.
- Not compatible with 265V hardwire setups — see the PTC154J sibling model, which requires the Amana PTSB4**E sub-base or PTPWHWK4 hard-wire kit with PSHW04A disconnect.
- Wall Sleeve NOT included — must be purchased separately.
- Exterior Architectural Grille NOT included — must be purchased separately.
- Not a drop-in fit for non-standard sleeve openings outside 42 in x 16-1/16 in.
| Attribute | Detail |
|---|---|
| Refrigerant Type | R-32 |
| Electrical Compliance | Factory LCDI power cord per UL 484 (units under 250V) |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Voltage Operating Range | Min 197V / Max 253V (230/208V models) |
Frequently Asked Questions
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This unit installs into a standard 42-inch x 16-1/16-inch PTAC wall sleeve opening, such as the WS900E or WS900QW series, which must be ordered independently.
What breaker size and plug type does this unit require?
With the 5.0/4.1 kW electric heater installed, this unit has an MCA of 27.6 amps and a maximum overcurrent protection (MOP) rating of 30 amps. It ships with a factory NEMA 6-30P power cord for 230/208V circuits.
Can this be hardwired for 265V commercial applications?
No. This is a 230/208V model and is not rated for 265V circuits. The 265V commercial version of this chassis is the PTC154J, which requires an Amana sub-base (PTSB4**E series) or hard-wire kit PTPWHWK4 with disconnect switch PSHW04A.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
[NEEDS VERIFICATION] Installation labor and licensing requirements are not specified in the source catalog data for this SKU. Refer to the manufacturer warranty document in the Resources tab for installation conditions that affect warranty validity.
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes. This chassis fits the industry-standard 42-inch wide x 16-1/16-inch high wall sleeve opening. It is not a fit for non-standard or custom sleeve openings outside those dimensions.
Warranty & Registration
This unit carries a 1-Year Repair/Replace warranty and a 5-Year Parts Limited Warranty on covered components. Exact terms, including any distinctions between commercial hospitality usage and residential usage, are detailed in the manufacturer warranty document — refer to the "Resources (System Manuals and Warranty)" Tab above on this page for full terms before you order.
