This is a wall-sleeve air conditioner and electric-heat unit built for hotel rooms, apartments, or additions where central ductwork isn't available. It's a 265V commercial configuration for property managers and electricians who need self-contained, per-room climate control on a dedicated 265V circuit.
This PTAC configuration pairs a 14,800 BTU cooling chassis with a 2.5 kW electric heat strip on a 265V circuit, a common setup in hotel corridors and multi-family properties where 265V distribution panels are already in place. The chassis meets or exceeds ASHRAE 90.1 efficiency requirements. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fit & Power Requirements
- Wall sleeve opening: Standard 42 in wide x 16-1/16 in high (WS900E / WS900QW series sleeves).
- Voltage: 265V. Voltage operating range 239V-292V minimum/maximum.
- Amperage with heat: 9.7A total amps, 12.2A MCA, 15A MOP.
- Power cord/plug: 7-20P, factory-installed. 265V units require factory-installed cartridge-style time-delay fuses.
- Wall Sleeve is NOT included and must be ordered separately.
- Exterior Architectural Grille is NOT included and must be ordered separately.
- This unit requires an Amana sub-base (PTSB4**E) or hard-wire kit PTPWHWK4 with disconnect switch PSHW04A — neither is included.
- Not compatible with 115V circuits.
- Not compatible with 230/208V circuits — for a 230/208V version of this chassis, see sibling model PTC153J.
- Not a drop-in replacement for non-standard or custom wall sleeve openings.
On 265V hospitality retrofits, techs sometimes reach for a standard sub-base without confirming it's rated for the heater's 12.2A MCA draw — undersized sub-base wiring under load is a slow-building fire risk, not an immediate trip. Verify the sub-base or hard-wire kit (PTPWHWK4 with PSHW04A disconnect) is rated for the full 15A MOP before energizing the circuit, and torque terminal lugs to the manufacturer's spec rather than "snug." Cross-check the receptacle or hardwire terminals against a NEMA receptacle chart before final connection — a 7-20P cord end on a mismatched receptacle is the single most common callback on 265V jobs. This is a property-management best practice on multi-unit turnovers: log the sub-base model and fuse rating on the room's maintenance card so the next tech doesn't have to re-verify from scratch.
Key Benefits
- 14,800 BTU/h cooling capacity with a 10.7 EER rating.
- 4.4 pints/hour of dehumidification at rated conditions.
- 65 CFM of dedicated ventilation (fresh make-up air) capability.
- Single-stage 2.5 kW electric heat strip delivers 8,500 BTU/h of supplemental heat at 265V.
- R-32 refrigerant chassis, meets or exceeds ASHRAE 90.1.
- Net unit weight of 113 lb keeps sleeve-removal and service manageable for a single technician.
Technical Table
| Spec | Value | Unit |
|---|---|---|
| Cooling Capacity | 14,800 | BTU/h |
| Heating Capacity (265V) | 8,500 | BTU/h |
| Electric Heat Strip Size | 2.5 | kW |
| Electric Heat Stages | 1 | stage |
| EER | 10.7 | - |
| Voltage | 265 | V |
| Compressor Amps | 6.3 | A |
| Compressor Watts | 1,380 | W |
| MCA (No Heater) | 7.4 | A |
| Total Watts (With Heat) | 2,570 | W |
| Total Amps (With Heat) | 9.7 | A |
| MCA (With Heat) | 12.2 | A |
| MOP | 15 | A |
| NEMA Plug Type / Power Cord | 7-20P | - |
| CFM Wet (High/Low) | 400/314 | CFM |
| CFM Dry (High/Low) | 414/414 | CFM |
| Ventilation CFM | 65 | CFM |
| Dehumidification | 4.4 | pints/hr |
| Net Weight | 113 | lb |
| Shipping Weight | 130 | lb |
| Refrigerant Type | R-32 | - |
| Wall Sleeve Dimensions | Standard 42 x 16-1/16 | in |
| Wall Sleeve Included | Not Included | - |
| Exterior Architectural Grille Included | Not Included | - |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Fits industry-standard 42 in x 16-1/16 in wall sleeve openings (WS900E / WS900QW-compatible chassis).
- Compatible with 265V circuits within a 239V-292V operating range, via 7-20P power cord.
- Requires an Amana PTSB4**E sub-base or PTPWHWK4 hard-wire kit with PSHW04A disconnect (sold separately) — this is mandatory for all 265V installations, not optional.
- Not compatible with 115V circuits.
- Not compatible with 230/208V circuits — for that voltage class on this chassis, see sibling model PTC153J.
- Wall sleeve and exterior architectural grille are NOT included; order separately.
- Not a drop-in fit for non-standard or custom-depth sleeve openings.
Compliance & Environment
| Item | Detail |
|---|---|
| Refrigerant Type | R-32 |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Overcurrent Protection | 15A MOP; 265V models require factory-installed cartridge-style time-delay fuses |
| Electrical Code Note | Units under 250V ship with an LCDI power cord per UL 484; this 265V unit does not use an LCDI cord |
| Voltage Operating Range | 239V minimum / 292V maximum for 265V models |
FAQ
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This unit fits the industry-standard 42 in wide x 16-1/16 in high wall sleeve opening (compatible sleeve models include WS900E and WS900QW), but you must order the sleeve and exterior grille independently.
What breaker size and plug type does this unit require?
With the 2.5 kW electric heat strip active, this unit has an MCA of 12.2A and a maximum overcurrent protection (MOP) rating of 15A. It ships with a 7-20P power cord for a 265V circuit. 265V models require factory-installed cartridge-style time-delay fuses.
Can this be hardwired for 265V commercial applications?
Yes. All 265V Amana PTAC models must be installed with an Amana sub-base (PTSB4**E series) or the PTPWHWK4 hard-wire kit paired with the PSHW04A disconnect switch. These are sold separately and are required for code-compliant 265V installation.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
This is a 265V commercial unit requiring a dedicated circuit, correct sub-base or hardwire kit, and NEC-compliant overcurrent protection. Installation by a licensed electrician or HVAC professional is strongly recommended. [NEEDS VERIFICATION - exact warranty installation requirements are detailed in the manufacturer warranty document in the Resources tab]
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes. This chassis fits the industry-standard 42 in x 16-1/16 in wall sleeve opening. It is not a drop-in fit for non-standard or custom sleeve openings.
Warranty & Registration
This unit carries a 1-Year Repair/Replace warranty and a 5-Year Parts Limited Warranty per manufacturer badge documentation. Commercial hospitality use may carry different terms or limitations than residential use — refer to the full warranty PDF in the "Resources (System Manuals and Warranty)" Tab above for exact coverage terms, exclusions, and registration requirements before purchase or install.
