This is a wall-sleeve heat pump air conditioner and heater for hotel rooms, apartments, or additions where central ductwork isn't available. It's built for property managers and electricians who need a self-contained, per-room heat pump on a 265V commercial circuit.
The PTH094J25AXXX is a 265V packaged terminal heat pump (PTHP) built for hospitality corridors, additions, and multi-family units where a heat pump reduces reliance on resistive electric heat during shoulder-season temperatures. Rated at 9,000 BTU/h cooling and 8,200 BTU/h heating pump capacity, with 2.5 kW of backup electric heat, it meets or exceeds ASHRAE 90.1. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fit & Power Requirements
- Wall sleeve opening: Standard 42 in wide x 16-1/16 in high (industry-standard PTAC/PTHP opening).
- Voltage: 265V commercial circuit only. Valid operating range 239V-292V.
- Amperage with heater: 9.7 total amps; MCA 12.2A; MOP 15A (cartridge-style time-delay fuses, factory-installed).
- Power cord/plug: NEMA 7-20P.
- Wall Sleeve is NOT included. Order separately (e.g., WS900E, WS900QW, or matched variant).
- Exterior Architectural Grille is NOT included. Order separately (SGK, AGK, or PGK series).
- Not compatible with 115V circuits.
- Not compatible with 230/208V circuits. If you need a 230/208V version of this chassis, see sibling model PTH093J.
- Requires an Amana sub-base (PTSB4**E series) or the PTPWHWK4 hardwire kit with PSHW04A disconnect switch for permanent 265V hardwire installs — neither is included.
- This unit does not ship with an LCDI power cord. LCDI cords apply only to units rated under 250V; this is a 265V unit.
On 265V installs, the most common callback is condensate pooling at the sleeve's inner lip, which happens when the sleeve is set level instead of pitched. The chassis's slide-out design means any standing water backs up into the wall cavity over time and softens the drywall around the sleeve flange. Pitch the sleeve 1/4 bubble toward the exterior wall using a torpedo level before final fastening, per the framing diagram on page 23 of the manufacturer catalog, so condensate always drains outward instead of inward. Separately, confirm the receptacle or sub-base is rated for the NEMA 7-20P cord configuration before energizing the circuit — mismatching a 265V heat pump to a 230V-rated receptacle is a fire-risk failure point, not just a fit issue. Property managers standardizing across a hotel floor should document sub-base model numbers per room on the electrical schedule so future PTAC swaps don't get bottlenecked by receptacle mismatches at 2 a.m.
Key Benefits
- Heat pump operation (8,200 BTU/h) reduces electric-heat runtime in mild weather, backed by 2.5 kW of electric heat for cold-snap coverage.
- EER 12.4 and COP 3.5 give a documented efficiency baseline for cooling and heat pump modes.
- Dehumidification rated at 2 pints/hr for comfort control in humid climates.
- Fresh air ventilation adjustable from 65-95 CFM for make-up air in occupied rooms.
- R-32 refrigerant, a lower-GWP option relative to older refrigerant blends.
- Meets or exceeds ASHRAE 90.1 efficiency standards.
| Spec | Value | Unit |
|---|---|---|
| Cooling Capacity | 9,000 | BTU/h |
| Heating Capacity (Heat Pump) | 8,200 | BTU/h |
| Heating Capacity (265V Electric Heat) | 8,500 | BTU/h |
| EER | 12.4 | - |
| COP | 3.5 | - |
| Voltage | 265 | V |
| Cooling Amps (Compressor) | 3.5 | A |
| Cooling Watts (Compressor) | 725 | W |
| Heating Amps (Compressor) | 3.5 | A |
| Heating Watts (Compressor) | 685 | W |
| Electric Heat Size | 2.5 | kW |
| Electric Heat Stages | 1 | - |
| Total Heater Watts | 2,570 | W |
| Total Amps (with Heater) | 9.7 | A |
| MCA | 12.2 | A |
| MOP | 15 | A |
| Power Cord / Plug Type | NEMA 7-20P | - |
| Refrigerant Type | R-32 | - |
| CFM Wet (High/Low) | 290/264 | CFM |
| CFM Dry (High/Low) | 320/320 | CFM |
| Fresh Air Vent | 65-95 | CFM |
| Dehumidification | 2 | pints/hr |
| Net Weight | 102 | LB |
| Shipping Weight | 117 | LB |
| Wall Sleeve Dimensions | Standard 42 x 16-1/16 | in |
| Wall Sleeve Included | Not Included | - |
| Exterior Architectural Grille Included | Not Included | - |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Fits the industry-standard 42-inch x 16-1/16-inch wall sleeve opening.
- Compatible with 265V commercial circuits (239V-292V operating range) using a NEMA 7-20P plug configuration, when paired with a matched sub-base or hardwire kit.
- Not compatible with 115V circuits.
- Not compatible with 230/208V circuits — for that voltage, see sibling model PTH093J.
- Wall Sleeve NOT included — must be purchased separately (WS900E, WS900QW, or matched variant).
- Exterior Architectural Grille NOT included — must be purchased separately (SGK, AGK, or PGK series).
- Not a drop-in replacement for non-standard or custom sleeve openings without verifying dimensions.
- Requires Amana sub-base (PTSB4**E) or PTPWHWK4 hardwire kit with PSHW04A disconnect for hardwire installs — sold separately.
| Attribute | Value |
|---|---|
| Refrigerant Type | R-32 |
| Efficiency Standard | Meets or exceeds ASHRAE 90.1 |
| Electrical Code Reference | Cartridge-style time-delay fuses required for 265V units (factory-installed); NEC-compliant overcurrent protection at 15A MOP |
| LCDI Cord Applicability | Not applicable to this 265V unit (LCDI ships only on units under 250V per UL 484) |
FAQ
Is the wall sleeve included with this unit?
No. The wall sleeve is sold separately. This unit fits the industry-standard 42-inch x 16-1/16-inch sleeve opening (WS900E / WS900QW or compatible models), but the sleeve and the exterior architectural grille must be ordered separately.
What breaker size and plug type does this unit require?
This 265V unit with its 2.5 kW electric heat draws a total of 9.7 amps, with a Minimum Circuit Ampacity (MCA) of 12.2 amps. Maximum Overcurrent Protection (MOP) is 15 amps, and 265V models require factory-installed cartridge-style time-delay fuses. It ships with a NEMA 7-20P power cord.
Can this be hardwired for 265V commercial applications?
Yes, and it must be paired with an Amana-brand accessory to operate safely. All 265V models require either an Amana sub-base (PTSB4**E series) or the PTPWHWK4 hardwire kit with the PSHW04A disconnect switch. Neither accessory is included with this unit.
Does this require a licensed electrician or HVAC professional to install and keep the warranty valid?
[NEEDS VERIFICATION] - Exact installer-licensing warranty conditions are not confirmed in the provided specification data. Refer to the warranty PDF in the Resources (System Manuals and Warranty) tab for the manufacturer's precise installation requirements.
Will this fit a standard 42-inch by 16-inch wall sleeve opening?
Yes. This chassis is designed for the industry-standard 42-inch wide x 16-1/16-inch high sleeve opening. It is not a drop-in fit for non-standard or custom sleeve openings without verifying dimensions first.
Warranty & Registration
This unit carries a 1-Year Repair/Replace warranty and a 5-Year Parts Limited Warranty per manufacturer badge documentation. Exact terms, including any distinction between residential and commercial/hospitality usage, are detailed in the warranty PDF located in the "Resources (System Manuals and Warranty)" Tab above on this page. Ask us before you order if you need clarification on coverage for a commercial hospitality install versus residential use — we always reply back.
