This is the I-Beam mounting kit for Skyblade HVLS ceiling fans, built for shops and warehouses hanging fans from structural I-beam supports rather than purlins or unistrut.
Skyblade HVLS fans move a lot of air and hang a long way above the floor, so the mounting hardware carries real consequence if it's mismatched to the structure. This I-Beam kit is engineered specifically for that support type, pairing a powder-coated chassis with stainless steel safety brackets so the fan stays put through daily vibration and thermal cycling. Note: If you would like to review the manufacturer Product Specifications, Warranty, Brochure, etc., for this system, please refer to the "Resources (System Manuals and Warranty)" Tab above on this page.
Critical Fitment & Requirements
- Designed specifically for mounting Skyblade HVLS fans to structural I-Beam supports.
- Includes 1/4" powder-coated guy wires/gripple hardware and powder-coated chassis.
- Stainless steel safety brackets included in the kit.
- NOT compatible with purlin ceiling braces - use the BP-913 Purlin Mounting Kit for that application.
- NOT compatible with unistrut or angle iron ceiling structures - separate mounting kits are required for those.
Guy wire tension gets overlooked on I-Beam installs, and uneven tension is the friction point that leads to fan wobble and premature bearing wear over time. Even, correctly torqued tension across all guy wires keeps the fan chassis level and reduces vibration transfer into the beam and roof deck, which is what actually prevents long-term structural fatigue and noise complaints on the shop floor. Check level with a torpedo level at the chassis before final tightening, and always verify the stainless safety brackets are seated and secured as a secondary fall-arrest point, not just the guy wires. Follow the OEM structural load limits for the I-Beam and fan combination before final sign-off - don't rely on field judgment alone.
Key Benefits
- Powder-coated chassis resists corrosion in shop and warehouse environments.
- Stainless steel safety brackets included for secure secondary support.
- 1/4" guy wire/gripple hardware sized for HVLS fan loads.
- Purpose-built for I-Beam structures - no field modification needed.
- Hardware included, so you're not sourcing separate fasteners.
| Spec | Value | Unit |
|---|---|---|
| Mounting Type | I-Beam | - |
| Guy Wire/Gripple Diameter | 1/4 | in |
| Chassis Finish | Powder-coated | - |
| Safety Bracket Material | Stainless steel | - |
| SKU | BP-915 | - |
Note: See "Resources (System Manuals and Warranty)" Tab above for full specifications.
Compatibility & Fitment
- Fits: Skyblade HVLS ceiling fans mounted to structural I-Beam supports.
- Does NOT fit: purlin ceiling braces (requires BP-913 Purlin Mounting Kit).
- Does NOT fit: unistrut mounting configurations (requires a unistrut-specific kit).
- Does NOT fit: angle iron mounting configurations (requires an angle iron-specific kit).
Compliance & Environment
| Item | Detail |
|---|---|
| Safety Bracket Material | Stainless steel |
| Chassis/Guy Wire Finish | Powder-coated |
| Structural Load Limits | [NEEDS VERIFICATION] - refer to Resources tab |
Options & SKUs
| Variant | SKU | Price |
|---|---|---|
| I-Beam | BP-915 | $420.00 |
FAQ
Does this kit fit a purlin ceiling brace?
No. The BP-915 kit is built for I-Beam mounting only. If you are hanging a Skyblade fan from a purlin ceiling brace, you need the BP-913 Purlin Mounting Kit instead.
What hardware is included with the BP-915 I-Beam Mounting Kit?
The kit includes 1/4-inch powder-coated guy wires/gripple hardware, a powder-coated chassis, and stainless steel safety brackets. All hardware needed for I-Beam mounting is included.
Can I use this kit with unistrut or angle iron ceilings?
No. This SKU is specific to I-Beam mounting. Unistrut and angle iron mounting kits are separate products for those structural configurations.
Is the safety bracket hardware rated for outdoor or corrosive environments?
The safety brackets are stainless steel and the chassis and guy wires are powder-coated for corrosion resistance. [NEEDS VERIFICATION] for specific outdoor/corrosive-environment ratings - refer to the Resources tab for manufacturer environmental specifications.
Warranty & Registration
Manufacturer warranty terms for this mounting kit are not detailed in the data provided. [NEEDS VERIFICATION] Please refer to the "Resources (System Manuals and Warranty)" Tab above for the manufacturer's warranty documentation. Ask us before you order if you need the warranty terms confirmed in writing - we always reply back.
